cancel
Showing results for 
Search instead for 
Did you mean: 

POE module of ICX 7450 24P is not working ?

abilashpr
Contributor III
I tried to enable POE on ICX 7450-24P, but it doesn't show any output.

Core#show po
  poe                         inline power information
  port                        Show port security
  power-savings-statistics    Power savings  statistics
Core#show poe
  DECIMAL      UNIT-ID
  STACKID/SLOT/PORT
  debug-info   show inline power debug information
  detail       show inline power detailed information
  emesg        Event Trace Logging messages
  pd           show pd ports power
Core#show poe
Core#show in
  inline                      inline power information
  interfaces                  Port status
Core#show inline power
  power   show inline power
Core#show inline power
  DECIMAL      UNIT-ID
  STACKID/SLOT/PORT
  debug-info   show inline power debug information
  detail       show inline power detailed information
  emesg        Event Trace Logging messages
  pd           show pd ports power
  |            Output modifiers
 
Core#show inline power 1/1/1
Core#
I tried to upgrade the POE firmware on this switch, but the Switch reboots and doesn't upgrade the firmware. 

I am running latest 8090.

Stack unit 1:
  Compressed Pri Code size = 32454872, Version:08.0.90T213 (SPR08090.bin)
  Compressed Sec Code size = 32454872, Version:08.0.90T213 (SPR08090.bin)
  Compressed Pri Boot Code size = 786944, Version:10.1.15T215 (spz10115)
  Compressed Sec Boot Code size = 786944, Version:10.1.15T215 (spz10115)
  Code Flash Free Space = 1578074112
Core#
Any help appreciated.

Regards,
Abilash PR.
5 REPLIES 5

jijo_panangat
RUCKUS Team Member
Hello Abi,

Could you post the below outputs here,

show version
show chassis
show inline power detail



Thanks
Jijo 

abilashpr
Contributor III
Hi Jijo,

Please find the requested output,

SSH@Core#show version
  Copyright (c) Ruckus Networks, Inc. All rights reserved.
    UNIT 1: compiled on Feb 19 2019 at 13:48:49 labeled as SPR08090
      (32454872 bytes) from Primary SPR08090.bin (UFI)
        SW: Version 08.0.90T213 
      Compressed Primary Boot Code size = 786944, Version:10.1.15T215 (spz10115)
       Compiled on Sun May 17 23:50:23 1936
  HW: Stackable ICX7450-24-HPOE
  Internal USB: Serial #: 9900617111400054
      Vendor: ATP Electronics, Total size = 1919 MB
==========================================================================
UNIT 1: SL 1: ICX7450-24P POE 24-port Management Module
      Serial  #:CYU3305P007
      Software Package: ICX7450_L3_SOFT_PACKAGE   (LID: eawIIFKrFFM)
      Current License: l3-prem  
      P-ASIC  0: type B548, rev 01  Chip BCM56548_A0
==========================================================================
UNIT 1: SL 2: ICX7400-4X1GF 4-port 4G Module
      Serial  #:CYY3338N01W
==========================================================================
 1000 MHz ARM processor ARMv7 88 MHz bus
 8192 KB boot flash memory
 2048 MB code flash memory
 2048 MB DRAM                                                     
STACKID 1  system uptime is 22 hour(s) 25 minute(s) 16 second(s) 
The system started at 17:47:33 GMT+04 Sat Jan 18 2020
The sy
SSH@Cshow chassis
The stack unit 1 chassis info: 
Power supply 1 (AC - Regular) present, status ok
        Model Number:   23-0000144-02
        Serial Number:  CZG2L33N07Z 
        Firmware Ver:   32.67
Power supply 1 Fan Air Flow Direction:  Front to Back
Power supply 2 (AC - Regular) present, status ok
        Model Number:   23-0000144-02
        Serial Number:  CZG2L41N17F 
        Firmware Ver:   32.67
Power supply 2 Fan Air Flow Direction:  Front to Back
Fan 1 ok, speed (auto): [[1]]<->2
Fan 2 ok, speed (auto): [[1]]<->2
Fan controlled temperature: 40.2 deg-C
Fan speed switching temperature thresholds:
                Speed 1: NM<----->60       deg-C
                Speed 2:       50<-----> 80 deg-C (shutdown)
Fan 1 Air Flow Direction:  Front to Back 
Fan 2 Air Flow Direction:  Front to Back                          
Slot 1 Current Temperature: 30.3 deg-C (Sensor 1), 39.6 deg-C (Sensor 2), 40.1 deg-C (Sensor 3), 28.0 deg-C (Sensor 4)
Slot 2 Current Temperature: 30.7 deg-C (Sensor 1)
Slot 3 Current Temperature: Empty / Powered Down
Slot 4 Current Temperature: Empty / Powered Down
        Warning level.......: 70.0 deg-C
        Shutdown level......: 80.0 deg-C
Boot Prom MAC : d4c1.9e2a.27b0
Management MAC: d4c1.9e2a.27b0
SSH@Core#show inline power detail
SSH@Core#
Appreciate your help!!!

Regards,
Abilash PR.

jijo_panangat
RUCKUS Team Member
Hi Abilash,

The power supply installed is regular one and not POE compliant. You need to change the ps module to power PD devices.

Thanks 

abilash_pr_ir5b
New Contributor III
Hi Jijo,

Thank you for the clarification, this really helped solving an issue which is 2 years old.

Regards,
Abilash PR.