cancel
Showing results for 
Search instead for 
Did you mean: 

When roaming from one AP to another, dropping telnet sessions

david_howard_h1
New Contributor II
We have a 5 week old Ruckus install. All firmware is current. Over the last 8 days, we have started to experience telnet sessions dropping and resetting our people in a specific application when they hand off from one AP to another (which causes the app to hang and Administrator intervention is needed to resolve every time). Prior to 8 days ago, this was not an issue. Yes, we've looked at Windows updates (we even rolled back test machines to July of this year). Still the same issue. Is there a chance that a long term setting (like channelfly or something) is causing this to start happening because it took time for said setting to do it's job? We're past the basic troubleshooting, we're having to get into the "odd, nobody thought of that" category. Yes we have a ticket open with support, but we're not moving forward much over the last 4 days on that front. Anyone?
8 REPLIES 8

andrea_coppini
Contributor II
Are you tunnelling?

Do you have proper coverage overlap between your APs?  The client might be disconnecting/connecting instead of roaming, which will cause the Telnet session to timeout.

Keep in mind that roaming is a 100% client-side operation, the infrastructure can only assist in the roam, not control it.

alexandra_frinc
New Contributor III
Hi David, 

Welcome to the forum and thanks for sharing your situation. 

There was a similar discussion in the past, maybe it is related:

wireless handheld devices losing telnet connection

You should check if something change in your environment in the last 8 days (New rogue APs, new sources of RF interference for which you should use a spectrum analyzer).  
Try to see if the issue happens with ChannelFly disabled. 

Regards, 
Alex

david_howard_h1
New Contributor II
Thank you both for taking the time to reply. To Alex: Yes we have seen that discussion and it does not seem to fit/apply to what we're experiencing. 

To Andrea: We have great coverage and overlap, and do have the auto tuning function enabled to try to help us keep that in good shape. In a couple of instances, we have manually set power settings on APs. We're aware of the decision to change AP's lay within the client itself. However, as mentioned hasn't been a problem until these 8 days. To Alex's point about new things, we've gone through those gymnastics because the first thing we said was "what has changed". Clearly something is different, but we cannot find it. The obvious stuff of new interference, AP's, etc has not proven to be a path that has answers. Windows updates were being looked at. We're even looking through the logs of the controller to see if it auto updated something that we didn't mean for it to do. So far, the level 1/level 2 kind of thought process hasn't been working. Hence, asking for the oddball thinking, because so far, no answers on our end either.

Please continue to ask questions of us, might make us say "oh crap" but so far these are questions asked/answered to at least a level of "doesn't seem to make a difference". Thanks again!

alex_shalima
Contributor
Hi David,

It sounds like your network stack is experiencing a change whenever "roaming" is occurring. Telnet session is nothing but an TCP socket. There is something causing this socket to reset or time-out.

To reset a socket you would have to have a topology change on Layer 2 or Layer 3 of your network stack (VLAN change or IP change).

To time-out a socket you simply take longer time to reply to an active TCP session. Many factors can contribute to this, including but not limited to interference or latency on the network. This can simply be tested with PINGing your server and walk around the building and check your reply times and packet drop rate. With Ruckus roaming you should not loose more than a packet or two in ideal situation.

From the data above:

1. Are you using VLAN Pooling (are you changing VLANs)
2. Are you using Dynamic VLANs by chance?  (again, are you changing VLANs)
3. Are you using AAA RADIUS Authentication for your clients? (does your TCP socket time out before you get re-authenticated)


Best,
Alex