Ruckus DHCP Relay != Cisco/HP DHCP Relay

[mark_buteyn]

I'm working on configuring WLANs with vlan tagging.  My understanding of DHCP relay from my networking background is a way of relaying DHCP request between different vlans.  DHCP relay in the Ruckus world is a way of broadcast traffic management.  Can someone correct me if I'm wrong?

If I'm right, I'm running stuck.  I've trolled the forums for a while trying to find similar situations.  

DHCP server on vlan 10 and it has two scopes: main network: 10.0.0.0/16 (for vlan 10) and guest network: 10.1.0.0/16 (for vlan 20). I have an L3 switch that does the DHCP relay (using ip helper-address). Router is configured properly too.

I connect a laptop via wired connection to a port with a vlan assignment of 20  The laptop gets an IP address in the 10.1.0.0/16 subnet and all is well.  

I disconnect the wired and connect the wireless to a vlan 20 tagged WLAN and it doesn't get an IP address at all.  Wireshark shows no DHCP responses coming back.  

I configured the WLAN with Ruckus' DHCP relay per documentation and I get an address back in the 10.0.0.0/16 scope.

What doesn't make sense to me is if I have a WLAN with vlan tagging, shouldn't that be the same as plugging in a wired connection to a vlan tagged port?

[michael_brado]

Mark, you are on the right track. 

Two ideas come to mind.

Confirm that VLAN 20 is being trunked to the AP switch port, and that you are not tunneling the WLAN back to the ZD, unless you have VLAN 20 trunked to your ZD switch port.

[mark_buteyn]

Thanks Michael.

I can confirm that vlan 20 is being trunked all the way.  Should have mentioned that the AP that I'm connecting to is plugged in to the same switch that I use for testing the wired connection I mentioned earlier.  If I set a static IP on the laptop's wireless connection all is well.  It just seems to be getting the DHCP back.

By tunneling, you are referring to Configure > WLANs > Edit SSID > Advanced Options > Tunnel Mode right?  That's checkbox is clear right now.

[eizens_putnins]

As much as I understand, you try to get tagged WLAN adapter interface. For my understanding it is not possible (WLAN card doesn't support it), and this would be double tagging anyway.
When you mention connecting laptop to port in 20 VLAN through wired connection, what do you actually mean -- connecting to access port in VLAN 20 (than laptop interface is untagged), or to trunk with VLAN 20 tagged  (than laptop interface must be tagged by tag 20 -- it is supported by most modern cards)?

Anyway, WLAN AP (any, not specifically Ruckus) will just add VLAN tag 20 to traffic coming from WLAN assigned to VLAN 20. So when connecting to this WLAN you essentially connect to access port in VLAN 20.

If you are connecting properly, but it still doesn't work, check if you are connecting AP to proper port -- usually if you can't get DHCP, it means that proper VLAN isn't actually present on AP port, or VLAN isn't connected somewhere on trunks if there are multiple switches .
Hope it helps,
Eizens

[mark_buteyn]

Thanks Eizens

Laptop wired is connecting to an access port in vlan 20.  The port is untagged in vlan 20.

Right, my understanding was that the AP adds the vlan tag and the WLAN is essentially an access port which is why I confused as to why I the DHCP relay works for wired access port but not the WLAN "access port".

Can anyone confirm that "DHCP Relay" means something different to Ruckus than it does to Cisco / HP?