Updating our Ruckus system in a Lennar home

[kaz]

We've been having inconsistent or slow Wi-Fi in certain rooms (they're at the corners of the house, so not surprising). After troubleshooting, I've decided that adding a Ruckus access point may be a reasonable solution. But in trying that, I've encountered some hurdles and am hoping someone in the community or Ruckus could offer advice.

1. Lennar didn't leave us with Ruckus login info when we bought the new home, so I don't know how to get into the system to check or modify things. What app/website should I use to get in?
2. Our house has a 7150 switch in the electric box, and what seem to be two R510 access points. I bought an R650 today and connected it to a port in a room that is connected to the 7150, but the R650 doesn't light up. Even if I connect the R650 to one of the ports on the 7150 that was used to go into an R510, it gets powered on but doesn't provide Wi-Fi.

Thanks!

Kaz

[kaz]

I see on the Unleashed dashboard that 159 is the R650 and 132 is the R510. So does the switch take on the same IP address as the Master (R510)?

[Vásquez_Fer]

Hi @kaz 

That IP address is from the Access Point we are looking the IP address from the ICX-Switch , sometimes it shows as unknown device , ruckus switch or router , ICX-7150 C12 P , or unidentified.

Correct the switch should be on the same range between 192168.0.1 to 192.168.0.254

Maybe if you can login in into your router you can locate the IP address for your switch most of the times your  local router is 192.168.0.1 or 192.168.0.254 copy and past these IPs on a URL. 

OR reboot your local router  ISP to refresh the IP addressing. 

Best Regards

Fernando Vasquez 

[kaz]

I found the MAC address of the 7150 and it corresponds to the device with 192.168.0.134 in the IP Scanner. Using that, I still have the same problem:

➜ ~ ssh admin@192.168.0.134
ssh: connect to host 192.168.0.134 port 22: Connection refused
➜ ~ ssh-keygen -R 192.168.0.134
Host 192.168.0.134 not found in /Users/kaz/.ssh/known_hosts
➜ ~ ssh super@192.168.0.134
ssh: connect to host 192.168.0.134 port 22: Connection refused

[Vásquez_Fer]

Hi @kaz 

Please do telnet option following command :  

nc 192.168.0.134 23

 Best Regards 

Fernando Vasquez

[kaz]

That worked! Here's what I get:

telnet@ICX7150-C12-Switch>enable

enable

No password has been assigned yet...

telnet@ICX7150-C12-Switch#show version

show version

  Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.

    UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a

      (24723488 bytes) from Primary SPS08061a.bin

        SW: Version 08.0.61aT211

      Compressed Boot-Monitor Image size = 786944, Version:10.1.10T225 (mnz10110)

       Compiled on Sun Jun 25 09:25:15 2017

  HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

      Serial  #:FEK3234N083

      Current License: 2X1G

      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

 1000 MHz ARM processor ARMv7 88 MHz bus

 8192 KB boot flash memory

 2048 MB code flash memory

 1024 MB DRAM

STACKID 1  system uptime is 3 day(s) 20 hour(s) 35 minute(s) 20 second(s)

--More--, next page: Space, next line: Return key, quit: Control-cshow inline power

The system started at 00:02:11 GMT+00 Sat Jan 01 2000

The system : started=cold start

telnet@ICX7150-C12-Switch#inline power

Incomplete command.

telnet@ICX7150-C12-Switch#show inline power detail

show inline power detail

Power Supply Data On unit 1:

++++++++++++++++++

Power Supply Data:

++++++++++++++++++

Power Supply #1:

Max Curr:  2.3 Amps

Voltage:   54.0 Volts

Capacity:  124 Watts

PoePower:  124 Watts

POE Details Info. On Unit 1 :

General PoE Data:

+++++++++++++++++