Switch has corrupt kernel image

[cherian_jobs]

Hi 

My Rukus ICX7150-C12P has corrupt kernel image.

 It is no longer working after power outage had syst amber light, the power light is green

I have followed the instructions to do factory reset and software recovery which did not work.

I connected via SecureCRT and found the message " Error Corrupt Kernel Image"

I am looking for replacement or RMA.

ICX7150-Boot>

Ruckus Wireless Bootloader: 10.1.14T225 (Nov 15 2018 - 04:59:18 -0800)

Booted from partition 2
DRAM: Validate Shmoo parameters stored in flash ..... OK

ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0xa

device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Secondary

NAND read: device 0 offset 0x4000000, size 0x2000000
2 ecc_errors after reading 58b8000:58b9c00
iproc_nand_read_page returned 2
NAND read from offset 4000000 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from secondary, no valid image; trying to boot from primary
device 0 offset 0x0, size 0xc0000
BOOTING image from Primary

NAND read: device 0 offset 0x0, size 0x2000000
2 ecc_errors after reading 18b8000:18b9400
iproc_nand_read_page returned 2
NAND read from offset 0 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
ICX7150-Boot>

[Imran_ruckus]

Hi @cherian_jobs 

Greetings!!!

Thank you for reaching out to the RUCKUS Lennar Home Community. 

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that you are encountering issues when trying Software Recovery of the RUCKUS ICX-7150-C12P Switch that is stuck in the boot mode.

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

As you see the ‘boot>’ prompt, could you please proceed with executing setenv commands as described in the Software Recovery guide? (Refer to the below screenshot and guide link)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-a-Software-re...

Video Link: https://www.youtube.com/watch?v=Ql22blH_CGo

Additionally, please share a picture showing the Software Recovery cable connections between the RUCKUS Switch and the Laptop.

Please let me know how it goes.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Imran_ruckus]

Hi @cherian_jobs 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[Imran_ruckus]

Hi @cherian_jobs 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[Imran_ruckus]

Hi @cherian_jobs 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

If we do not receive a response from you within 24 hours from the timestamp of this message, your case will proceed to closure.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community