POE stopped working after power outage

[mbhinder]

My POE seems to have stopped working on my Lennar home after a recent power outage.

telnet@ICX7150-C12 Switch(config-if-e1000-1/1/1)#show version

  Copyright (c) Ruckus Networks, Inc. All rights reserved.

    UNIT 1: compiled on Aug  8 2023 at 22:55:03 labeled as SPS08095m

      (31457280 bytes) from Primary SPS08095m.bin (UFI)

        SW: Version 08.0.95mT211 

      Compressed Primary Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

       Compiled on Tue Nov 29 12:43:26 2022

  HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

      Serial  #:FEK3803S09T

      Software Package: BASE_SOFT_PACKAGE   

      Current License: 2X1G  

      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

telnet@ICX7150-C12 Switch(config-if-e1000-1/1/1)#show inline power

Power Capacity:    Total is 124000 mWatts. Current Free is 124000 mWatts.

Power Allocations: Requests Honored 0 times

 Port Admin Oper    ---Power(mWatts)---  PD Type  PD Class     Pri  Fault/

     State State   Consumed  Allocated                             Error

-----------------------------------------------------------------------------

  1/1/1 On Off            0          0  n/a      n/a            0  n/a

  1/1/2 On Off            0          0  n/a      n/a            0  n/a

  1/1/3 On Off            0          0  n/a      n/a            0  n/a

  1/1/4 On Off            0          0  n/a      n/a            0  n/a

  1/1/5 On Off            0          0  n/a      n/a            0  n/a

  1/1/6 On Off            0          0  n/a      n/a            0  n/a

  1/1/7 On Off            0          0  n/a      n/a            0  n/a

  1/1/8 On Off            0          0  n/a      n/a            0  n/a

  1/1/9 On Off            0          0  n/a      n/a            0  n/a

 1/1/10 On Off            0          0  n/a      n/a            0  n/a

 1/1/11 On Off            0          0  n/a      n/a            0  n/a

 1/1/12 On Off            0          0  n/a      n/a            0  n/a

-----------------------------------------------------------------------------

 Total                     0          0

--More--, next page: Space, next line: Return key, quit: Control-c^C

 Port Admin Oper    ---Power(mWatts)---  PD Type  PD Class     Pri  Fault/

     State State   Consumed  Allocated                             Error

-----------------------------------------------------------------------------

  1/1/1 On Off            0          0  n/a      n/a            0  n/a

  1/1/2 On Off            0          0  n/a      n/a            0  n/a

  1/1/3 On Off            0          0  n/a      n/a            0  n/a

  1/1/4 On Off            0          0  n/a      n/a            0  n/a

  1/1/5 On Off            0          0  n/a      n/a            0  n/a

  1/1/6 On Off            0          0  n/a      n/a            0  n/a

  1/1/7 On Off            0          0  n/a      n/a            0  n/a

  1/1/8 On Off            0          0  n/a      n/a            0  n/a

  1/1/9 On Off            0          0  n/a      n/a            0  n/a

 1/1/10 On Off            0          0  n/a      n/a            0  n/a

 1/1/11 On Off            0          0  n/a      n/a            0  n/a

 1/1/12 On Off            0          0  n/a      n/a            0  n/a

-----------------------------------------------------------------------------

 Total                     0          0

--More--, next page: Space, next line: Return key, quit: Control-c^C

I have enabled and disabled the ports repeatedly and the switch otherwise seems to be working fine. Any ideas?

[mbhinder]

This is resolved, I kept poking around and saw that the POE firmware wasn’t present. Factory reset and I noticed a log line that seemed to suggest it was downloading it. After a while it downloaded but then complained that the ports were overloaded. I changed the device type to class 4 and it worked. While I’m happy it worked eventually this equipment is obviously not for the average home buyer I don’t know what Lennar was thinking.

[Jayavidhya]

Hi @mbhinder 

Thanks for the update.

Good to hear that the issue got resolved. 

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community