I cannot reset my switch after power outage

[Nico]

I am getting this error message

Bytes transferred = 60795221 (39fa955 hex)
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from tftp, trying to boot from primary
device 0 offset 0x0, size 0xc0000
BOOTING image from Primary

NAND read: device 0 offset 0x0, size 0x2000000
8 ecc_errors after reading 1b48000:1b49c00
iproc_nand_read_page returned 2
NAND read from offset 0 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from primary, no valid image; trying to boot from secondary
device 0 offset 0x0, size 0xc0000
BOOTING image from Secondary

NAND read: device 0 offset 0x4000000, size 0x2000000
4 ecc_errors after reading 5b48000:5b49800
iproc_nand_read_page returned 2
NAND read from offset 4000000 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from primary, no valid image; trying to boot from secondary
device 0 offset 0x0, size 0xc0000
BOOTING image from Secondary

NAND read: device 0 offset 0x4000000, size 0x2000000
1 ecc_errors after reading 5b48000:5b48400
iproc_nand_read_page returned 2
NAND read from offset 4000000 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
ICX7150-Boot>

[Imran_ruckus]

Hi @Nico 

Greetings!!!

Thank you for reaching out to the RUCKUS Lennar Home Community. 

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that your RUCKUS ICX-7150-C12P Switch is not working after a power outage. 

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

To better assist you, could you please provide the following information:
When your switch is connected to the outlet, do you observe any illuminated lights (amber or green)? Kindly describe which lights are visible. Additionally, please provide a photo showing the status of the lights and the full switch panel with cable connections to the switch ports.

Please log into your RUCKUS Account before uploading these photos/screenshots.

Please help me with the above query and should you have any further questions or concerns, feel free to reach out. 

We appreciate your cooperation and look forward to resolving this matter for you promptly.

Best regards,

Imran Sanadi  
RUCKUS Lennar Home Community

[Nico]

[Imran_ruckus]

Hi @Nico 

Thank you for providing the information.

Could you please let me know if you tried hard resetting the RUCKUS ICX-7150-C12P Switch with a paper clip?

If not, I recommend attempting a physical factory reset multiple times, as outlined in our RUCKUS Lennar Knowledge Base self-help article accessible through this link and VIDEO: 

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/Process-for-performing-a-phy...

Video link: https://www.youtube.com/watch?v=6jHMTdo_hK4

If the initial reset attempts do not resolve the issue, please try resetting your switch multiple times (approximately 20-30 times) using the method described in the article. In some cases, repeated attempts have successfully resolved similar issues. Upon successful reset, the SYST and PWR lights should turn GREEN.

Please proceed with these steps and let me know if the switch powers on successfully afterward.

Thank you for your patience and cooperation in this matter.

Best regards,

Imran Sanadi  
RUCKUS Lennar Home Community

[Nico]

I tried to reset it 30 times but it still not working I getting the amber sys light