cancel
Showing results for 
Search instead for 
Did you mean: 

Cannot update icx7150

Rkeiser
New Contributor

Switch will not update firmware and when in cli it says it is in read only. Also when I try to configure ssl there is no start up config file. tried multiple times and says the same thing. when i show flash it shows "Compressed Pri Code size = 25976488, Version:08.0.80fT211 (SPS08080d.bin)
 Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPR08080d.bin)
 Compressed Boot-Monitor Image size = 786944, Version:10.1.15T225
" It wont take the actual image 08090f to upgrade to ufi.

26 REPLIES 26

Imran_ruckus
Moderator
Moderator

Hi @Rkeiser 

Greetings of the day!

Thank you for contacting Lennar Home Community.

Hope you are doing well!!!

Thank you for the detailed information you shared.

From the case description, I could understand that you are unable to Upgrade your RUCKUS ICX-7150-C12P Switch.

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command 

enable 

show version

show flash

Please let me know if you have any queries in this regard.

Thank you again.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

here is what it says when I entered the commands.
"


ICX7150-C12-Switch#show version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Apr 6 2020 at 22:29:25 labeled as SPS08080f
(25976488 bytes) from Primary SPS08080d.bin
SW: Version 08.0.80fT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.15T225 (mnz10115)
Compiled on Thu Jan 31 07:08:55 2019

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3816R0BB
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 2 day(s) 3 hour(s) 25 minute(s) 15 second(s)
The system started at 00:57:33 GMT+00 Sat Jan 01 2000

The system : started=warm start reloaded=by "reload"

==========================================================================
========== WARNING: Boot-monitor version mismatch!!! ==========
========== Please use "show boot-monitor" command for details ==========
==========================================================================
ICX7150-C12-Switch#
ICX7150-C12-Switch#
ICX7150-C12-Switch#
ICX7150-C12-Switch#
ICX7150-C12-Switch#
ICX7150-C12-Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25976488, Version:08.0.80fT211 (SPS08080d.bin)
Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPR08080d.bin)
Compressed Boot-Monitor Image size = 786944, Version:10.1.15T225
Code Flash Free Space = 1204994048"

Hi @Rkeiser 

Greetings!!!

Thank you for the response and the information you shared.

Please enter the below commands and retry Upgrading the Switch.

Note: Hit Enter to accept each command 

enable

boot system flash primary

Please share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Could not verify if the Running Config data has been changed.
Do you want to continue the reload anyway? (enter 'y' or 'n'): y
ICX7150-C12-Switch#Unmounting the External USB
We are in system resetcp: can't create '/fast_iron/logs/log_console.txt.gz': File exists
sh: can't create /fast_iron/logs/kmsg.txt: Read-only file system
cp: can't create '/fast_iron/support/fitrace/fitrace.errorlog': File exists

dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
mkdir: can't create directory '/fast_iron/.images': Structure needs cleaning
Creating TUN device
mv: can't rename '/fast_iron/logs/tpm_infra_init.log': Read-only file system
Starting TPM Infra
/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
Group tss and User tss created
/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
kernel.hostname = localhost
hostname set to localhost
/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
Starting TCSD Daemon
/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
TCSD Up and Running
/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
Enabling time stamp.
/etc/init.sh: line 1: can't create /fast_iron/logs/bootmsg: Read-only file system
^CCould not verify if the Running Config data has been changed.
Do you want to continue the reload anyway? (enter 'y' or 'n'): y
ICX7150-C12-Switch#Unmounting the External USB
We are in system resetcp: can't create '/fast_iron/logs/log_console.txt.gz': File exists
sh: can't create /fast_iron/logs/kmsg.txt: Read-only file system
cp: can't create '/fast_iron/support/fitrace/fitrace.errorlog': File exists

Invalid input -> dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base : 0x9f500000, warm_mem_len: 0xb00000
Type ? for a list
ICX7150-C12-Switch>mkdir: can't create directory '/fast_iron/.images': Structure needs cleaning
Invalid input -> mkdir: can't create directory '/fast_iron/.images': Structure n eeds cleaning
Type ? for a list
ICX7150-C12-Switch>Creating TUN device
Invalid input -> Creating TUN device
Type ? for a list
ICX7150-C12-Switch>mv: can't rename '/fast_iron/logs/tpm_infra_init.log': Read-o nly file system
Invalid input -> mv: can't rename '/fast_iron/logs/tpm_infra_init.log': Read-onl y file system
Type ? for a list
ICX7150-C12-Switch>Starting TPM Infra
Invalid input -> Starting TPM Infra
Type ? for a list
ICX7150-C12-Switch>/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm _infra_init.log: Read-only file system
Invalid input -> /etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_i nfra_init.log: Read-only file system
Type ? for a list
ICX7150-C12-Switch>Group tss and User tss created
Invalid input -> Group tss and User tss created
Type ? for a list
ICX7150-C12-Switch>/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm _infra_init.log: Read-only file system
Invalid input -> /etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_i nfra_init.log: Read-only file system
Type ? for a list
ICX7150-C12-Switch>kernel.hostname = localhost
Invalid input -> kernel.hostname = localhost
Type ? for a list
ICX7150-C12-Switch>hostname set to localhost
Invalid input -> hostname set to localhost
Type ? for a list
ICX7150-C12-Switch>/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm _infra_init.log: Read-only file system
Invalid input -> /etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_i nfra_init.log: Read-only file system
Type ? for a list
ICX7150-C12-Switch>Starting TCSD Daemon
Invalid input -> Starting TCSD Daemon
Type ? for a list
ICX7150-C12-Switch>/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm _infra_init.log: Read-only file system
Invalid input -> /etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_i nfra_init.log: Read-only file system
Type ? for a list
ICX7150-C12-Switch>TCSD Up and Running
Invalid input -> TCSD Up and Running
Type ? for a list
ICX7150-C12-Switch>/etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm _infra_init.log: Read-only file system
Invalid input -> /etc/tpm-infra.sh: line 108: can't create /fast_iron/logs/tpm_i nfra_init.log: Read-only file system
Type ? for a list
ICX7150-C12-Switch>Enabling time stamp.
Invalid input -> Enabling time stamp.
Type ? for a list
ICX7150-C12-Switch>/etc/init.sh: line 1: can't create /fast_iron/logs/bootmsg: R ead-only file system
Invalid input -> /etc/init.sh: line 1: can't create /fast_iron/logs/bootmsg: Rea d-only file system
Type ? for a list
ICX7150-C12-Switch>^CCould not verify if the Running Config data has been change d.
Invalid input -> ^CCould not verify if the Running Config data has been changed.
Type ? for a list
ICX7150-C12-Switch>Do you want to continue the reload anyway
Unrecognized command
ICX7150-C12-Switch> (enter 'y' or 'n'): y
Invalid input -> (enter 'y' or 'n'): y
Type ? for a list
ICX7150-C12-Switch>ICX7150-C12-Switch#Unmounting the External USB
Invalid input -> ICX7150-C12-Switch#Unmounting the External USB
Type ? for a list
ICX7150-C12-Switch>We are in system resetcp: can't create '/fast_iron/logs/log_c onsole.txt.gz': File exists
Invalid input -> We are in system resetcp: can't create '/fast_iron/logs/log_con sole.txt.gz': File exists
Type ? for a list
ICX7150-C12-Switch> sh: can't create /fast_iron/logs/kmsg.txt: Read-only file system
Invalid input -> sh: can't create /fast_iron/logs/kmsg.txt: Read-only file syste m
Type ? for a list
ICX7150-C12-Switch> cp: can't create '/fast_iron/support/fitrace/fitrace.errorlog': File exists
Invalid input -> cp: can't create '/fast_iron/support/fitrace/fitrace.errorlog': File exists