I am in Switch 1 and now I want to go to SW2 without logging out

[bgh]

Dear All,

Right now I am logged in to Switch 01.

I am finding a mac address by doing the LLDP command.

I am now trying to log in to SW02 from SW01.

What is command to login to SW02, without having to quit/exit from SW01

Please help.

This is my switch version

SSH@LONPR-SW01-B-CAB-A-MDF>show version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Oct 18 2018 at 14:24:35 labeled as SPS08080ca
(25967148 bytes) from Primary ICX7450/Images/SPS08080ca.bin
SW: Version 08.0.80caT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T215 (spz10113)
Compiled on Tue Jul 24 10:22:26 2018

HW: Stackable ICX7450-24
Internal USB: Serial #: 9901318050800029
Vendor: ATP Electronics, Total size = 1919 MB
==========================================================================
UNIT 1: SL 1: ICX7450-24 24-port Management Module
Serial #:CYT3336P00B
Software Package: BASE_SOFT_PACKAGE (LID: eavIIILrFFd)
Current License: l3-base
P-ASIC 0: type B548, rev 01 Chip BCM56548_A0
==========================================================================
UNIT 1: SL 2: ICX7400-4X1GF 4-port 4G Module
Serial #:CYY3309P007
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
2048 MB DRAM
STACKID 1 system uptime is 5 day(s) 1 hour(s) 9 minute(s) 1 second(s)
The system started at 08:40:12 GMT+00 Thu May 09 2024

The system : started=cold start
My stack unit ID = 1, bootup role = active

I have tried the following command so far

SSH@LONPR-SW01-B-CAB-A-MDF>show lldp neighbors detail ports ethernet 1/1/1
Local port: 1/1/1
Neighbor: c0c5.2050.8033, TTL 117 seconds
+ Chassis ID (MAC address): c0c5.2050.8020
+ Port ID (MAC address): c0c5.2050.8033
+ Time to live: 120 seconds
+ System name : "LONPR-SW02-B-CAB-A-MDF"
+ Port description : "GigabitEthernet1/1/20"
+ System capabilities : bridge
Enabled capabilities: bridge
+ 802.3 MAC/PHY : auto-negotiation enabled
Advertised capabilities: 10BaseT-HD, 10BaseT-FD, 100BaseTX-HD,
100BaseTX-FD, fdxSPause, fdxBPause,
1000BaseT-HD, 1000BaseT-FD
Operational MAU type : 1000BaseT-FD
+ Link aggregation: not capable
+ Maximum frame size: 1522 octets
+ Port VLAN ID: 1
+ Management address (IPv4): 10.164.11.172

SSH@LONPR-SW01-B-CAB-A-MDF>/system ssh 10.164.11.172 user=admin
Invalid input -> /system ssh 10.164.11.172 user=admin
Type ? for a list
SSH@LONPR-SW01-B-CAB-A-MDF>/system ssh 10.164.11.172 user=admin
Invalid input -> /system ssh 10.164.11.172 user=admin
Type ? for a list
SSH@LONPR-SW01-B-CAB-A-MDF>telnet 10.164.11.172
Invalid input -> telnet 10.164.11.172

[jdryan]

Hi bgh,

With regards to the query, Could you try the below on the enable prompt, and let us know if that helped.
Ex:

device> en
device# ssh user@10.164.11.172

or

device> en
device# ssh 10.164.11.172

And enter the username when prompted.

Thanks !