cancel
Showing results for 
Search instead for 
Did you mean: 

Unleashed app not working

Marvin2332
New Contributor

I keep trying to access the app and it tells me that I’m not connected to unleashes network. I have upgraded the app and it rebooted the AP’s (R320’s) but I’m still getting super low speeds. I need to fix issue

5 REPLIES 5

Vásquez_Fer
Moderator
Moderator

Hi @Marvin2332 

Hope you are doing well ! 

That there is a low speed does not depend on the Ruckus many times this depends on the ISP since the ruckus only distribute the connection through your house.

You must check the wiring to avoid any physical issue between the Access Point and ICX-7150-C12P

If there was a blackout or power outage and the switch reboot because of that, most possible your switch starts running the wrong code which we call ‘routing code’ this is a know issue that can create multiples issues on your network.

Vsquez_Fer_0-1670503167194.png

 

An identifier of this problem is that it comes out as Switch-Router in the unleashed dashboard.

There we are going to see 2 important things the

MAC address: Physical address of the device this never changes

The IP address is a logical address assigned by your local router (ISP) to the device (this can change and may not be the same as the one shown on the dashboard)

1- To fix this issue, we must identify the IP address of the switch 'currently'

-We can try the IP address that shows in the dashboard copy and paste it in the URL if that redirects you to the login page for the ICX-7150-C12P that is the correct one if not.

I will leave you a guide how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2-Once we identified the IP address of the switch proceed to access remote to the device 'command Line' 

How to remotely access to 'ICX 7150-12P' or 'access points' "Network devices"

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access to the Command line should look like this:

ICX7150-C12 Router>

3-Here is a quick guide to understand how to fix the 'routing code issue' but basically you need only need to run the following commands once you are on the command line 'CLI' 

Note: Hit Enter to accept each command

enable

copy flash flash secondary 

boot system flash secondary yes 

example: 

ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished )
ICX7150-24P Router#boot system flash secondary yes ( hit enter to accept the command  : the switch will reboot )

How to Fix Routing code issues on Lennar Home users

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-cod...

4-If the access via IP address is not possible here is a guide how to access to the Switch via console (cable access between your PC to the ICX 7150-C12P) in this case we need a USB type C to USB standard or Console cable Rj45 to USB. 

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

Once you are log in the ICX-7150-C12P please follow up the same steps that are on point '3'

Best Regards 

Fernando Vasquez 

So I completed all the steps, in the putt step it refers to the unit as ICX-7150-C12 switch>
yet the procedure states it should say ICX-7150-C12 router>. Never the less I completed all steps and rebooted the switch to the secondary flash but I still have slow speeds on WiFi. Yet hardwire everything is fine. My problem has not been solved!

Marvin2332
New Contributor

Will a factory reset of both access point units fix the issue of slow wireless speeds and no devices on 5G upstairs?

Hope you are doing well! 

Basically, the yellow light means that there are not clients connected on that specific Radio (5G or 2.4G) that depends where is the yellow light on.

Vsquez_Fer_0-1670503729229.jpeg

 

This does not mean that the Access Point is broken or damaged. 

Here is the meaning of each light on the Wireless Access Point

https://docs.commscope.com/bundle/unleashed-200.9-onlinehelp/page/GUID-19D4261B-D10B-4DE3-B63A-3498F...

Yellows light 2.4G: Radio is up, no clients are connected to the 2.4 GHz radio.
Yellows light 5G: Radio is up, no clients are connected to the 5 GHz radio.

So, if there is a device (iPhone) that is using the 5G radio, the light on the Access Point will be turning green on the 5G radio indicating that there is a client/device using that radio (5G)

More details for the radio 2.4G and 5G

A 2.4 GHz connection travels farther at lower speeds, while 5 GHz frequencies provide faster speeds at shorter range. What depends on whether to use 5g or 2.4G will depend on the end device (such as phones/pc/ring door/Mac devices/iPhone) They choose whether to use 2.4g or 5g auto. It will also depend on the network (Wi-Fi / SSID / WLAN ) configuration if it is 2.4 or 5G only.

A lot of electronic devices and appliances use the 2.4 GHz frequency, including microwaves, baby monitors, security cameras, and garage door openers and phones.

Vsquez_Fer_2-1670503729238.png

Create a  dedicated Network  '5G' or '2.4G' only

Creating a New Wireless WLAN (SSID)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Creating-a-New-Wireless-WLAN...

https://www.youtube.com/watch?v=JYONV1q1Zws&t=149s

Mobile APP

https://www.youtube.com/watch?v=L_oAReVK1qo&t=5s

Best Regards 

Fernando Vasquez