05-05-2023 01:32 AM
Hi guys,
I've been running Ruckus r550 APs for the last year or so at my small office. I jumped at the chance to get a used Ruckus 7150 c12 (my first time trying out a managed switched).
All of the ports work fine if I plug a power supplies into the Ruckus APs, but if i remove the power supplies, the c12 is only able to POE 4 APs, and it gives me the "power disabled on port XXX because of power management" message in console.
I've searched long and far and don't know what to do.
Below is the info from my switch via console (show version, show inline power, show inline power detail):
Thank you in advanced!
SSH@ICX7150-C12-Switch> show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Dec 16 2021 at 03:40:25 labeled as SPS08095f
(31457280 bytes) from Primary SPS08095f.bin (UFI)
SW: Version 08.0.95fT211
Compressed Primary Boot Code size = 786944, Version:10.1.21T225 (mnz10121)
Compiled on Wed Aug 25 06:27:49 2021
HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:XXXX
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 50 minute(s) 43 second(s)
The system started at 04:29:46 GMT+00 Fri Dec 17 2021
The system : started=warm start reloaded=by "reload"
SSH@ICX7150-C12-Switch>show inline power
Power Capacity: Total is 124000 mWatts. Current Free is 1600 mWatts.
Power Allocations: Requests Honored 595 times
Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/
State State Consumed Allocated Error
-----------------------------------------------------------------------------
1/1/1 On On 6300 28850 2P-IEEE Class 4 3 n/a
1/1/2 On Off 0 0 n/a n/a 3 n/a
1/1/3 On On 6500 28850 2P-IEEE Class 4 3 n/a
1/1/4 On Off 0 0 n/a n/a 3 n/a
1/1/5 On Off 0 0 n/a n/a 3 n/a
1/1/6 On Off 0 0 n/a n/a 3 n/a
1/1/7 On On 6200 28850 2P-IEEE Class 4 3 n/a
1/1/8 On On 6500 28850 2P-IEEE Class 4 3 n/a
1/1/9 On Off 0 0 n/a n/a 3 n/a
1/1/10 On Off 0 0 n/a n/a 3 n/a
1/1/11 On Off 0 7000 n/a n/a 3 n/a
1/1/12 On Off 0 0 n/a n/a 3 n/a
-----------------------------------------------------------------------------
Total 25500 122400
Power Supply Data On unit 1:
++++++++++++++++++
Power Supply Data:
++++++++++++++++++
Power Supply #1:
Max Curr: 2.3 Amps
Voltage: 54.0 Volts
Capacity: 124 Watts
PoePower: 124 Watts
POE Details Info. On Unit 1 :
General PoE Data:
+++++++++++++++++
Firmware
Version
----------------
02.1.8 Build 004
Hardware
Version
----------------
V2R4
Device HW version : 0:V2R4 1:V2R4
Device Temperature(deg-C) : 0:60 1:66
Device Status : 0:Good 1:Good
Cumulative Port State Data:
+++++++++++++++++++++++++++
#Ports #Ports #Ports #Ports #Ports #Ports #Ports
Admin-On Admin-Off Oper-On Oper-Off Off-Denied Off-No-PD Off-Fault
-------------------------------------------------------------------------
12 0 4 8 0 8 0
Cumulative Port Power Data:
+++++++++++++++++++++++++++
#Ports #Ports #Ports Power Power
Pri: 1 Pri: 2 Pri: 3 Consumption Allocation
-----------------------------------------------
0 0 12 26.400 W 122.400 W