r720 unleashed PoE+ not working

[giuseppe_lamber]

Hi All,

    I've got a couple of r720 unleashed to run in our small office. They are connected to a Brocade ICX6450-48p
I've ready probably everything about this topic before make my own post, and I'm sure I'm missing something, but I'm really out of ideas 😕
LLDP is enabled on both, AP and Switch, power-over-mdi is advertised by the switch, but yet no luck...the APs are stuck on 802.3af mode

from the switch:

 Port   Admin   Oper    ---Power(mWatts)---  PD Type  PD Class  Pri  Fault/
        State   State   Consumed  Allocated                          Error
--------------------------------------------------------------------------
  1/1/1 On      Off            0          0  n/a      n/a         3  PD Detection Fault
  1/1/2 On      Off            0          0  n/a      n/a         3  n/a
  1/1/3 On      On          9500      30000  802.3at  Class 4     1  n/a

Local port: 1/1/3
  Neighbor: 0060.0869.97ef, TTL 113 seconds
    + Chassis ID (MAC address): xxxxxxxxxxxxxx
    + Port ID (MAC address): xxxxxxxxxxxxxx
    + Time to live: 120 seconds
    + System name         : "Ruckus-Unleashed"
    + System description  : "Ruckus R720 Multimedia Hotzone Wireless AP/SW Ver\
                             sion: 200.5.10.0.291"
    + System capabilities : bridge, WLAN access point, router
      Enabled capabilities: bridge, WLAN access point
    + Management address (IPv4): 192.168.1.7
    + Port description    : "ent1"
    + Link aggregation: aggregated (aggregated port ifIndex: 11)
    + 802.3 MAC/PHY          : auto-negotiation not supported
      Operational MAU type   : 1000BaseT-FD
    + 802.3 Power via MDI: PD port
  Neighbor: 0060.0869.97ef, TTL 113 seconds
    + Chassis ID (MAC address): xxxxxxxxxxxxxx
    + Port ID (MAC address): xxxxxxxxxxxxxx
    + Time to live: 120 seconds
    + System name         : "Ruckus-Unleashed"
    + System description  : "Ruckus R720 Multimedia Hotzone Wireless AP/SW Ver\
                             sion: 200.5.10.0.291"
    + System capabilities : bridge, WLAN access point, router     
      Enabled capabilities: bridge, WLAN access point             
    + Management address (IPv4): 192.168.1.7                      
    + Port description    : "ent2"                                
    + Link aggregation: aggregated (aggregated port ifIndex: 11)  
    + 802.3 MAC/PHY          : auto-negotiation not supported     
      Operational MAU type   : 1000BaseT-FD                       
    + 802.3 Power via MDI: PD port                                
  Neighbor: 0060.0869.97ef, TTL 102 seconds                       
    + Chassis ID (MAC address):   xxxxxxxxxxxxxx      
    + Port ID (MAC address):         xxxxxxxxxxxxxx        
    + Time to live: 120 seconds                                   
    + System name         : "Ruckus-Unleashed"                    
    + System description  : "Ruckus R720 Multimedia Hotzone Wireless AP/SW Ver\
                             sion: 200.5.10.0.291"                
    + System capabilities : bridge, WLAN access point, router     
      Enabled capabilities: bridge, WLAN access point             
    + Management address (IPv4): 192.168.1.7                      
    + Port description    : "ent3"                                
    + Link aggregation: aggregated (aggregated port ifIndex: 11)  
    + 802.3 MAC/PHY          : auto-negotiation not supported     
      Operational MAU type   : 1000BaseT-FD                       
    + 802.3 Power via MDI: PD port               

From the AP

       AP:  ID:
    1:
      MAC Address= xx:xx:xx:xx:xx:xx
      Model= r720
      Approved= Yes
      Device Name= RuckusAP
      Device Role= Master
      Description= 
      Location= 
      GPS= 
      CERT = Normal
      Bonjour-policy= 
      Bonjour-fencing= 
      Group Name= System Default
      Channel Range:
        A/N= 36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,149,153,157,161 (Disallowed= )
        B/G/N= 1,2,3,4,5,6,7,8,9,10,11 (Disallowed= )
      Radio a/n:
        Channelization= Auto
        Channel= Auto
        WLAN Services enabled= Yes
        Tx. Power= Auto
        WLAN Group Name= Default
        Call Admission Control= OFF
        SpectraLink Compatibility= Disabled
      Radio b/g/n:
        Channelization= Auto
        Channel= Auto
        WLAN Services enabled= Yes
        Tx. Power= Auto
        WLAN Group Name= Default
        Call Admission Control= OFF
        SpectraLink Compatibility= Disabled
      Override global ap-model port configuration= No
      Network Setting:
        Protocol mode= IPv4-Only
        Device IP Settings= Manual
        IP Address= 192.168.1.7
        Netmask= 255.255.255.0
        Gateway= 192.168.1.1
        Primary DNS Server= 192.168.1.252
        Secondary DNS Server= 192.168.1.1
      Mesh:
        Status= Disabled
      LLDP:
        Status = Use Parent Setting
      LAN Port:
        0:
          Interface= eth0
          Dot1x= None
          LogicalLink= Down
          PhysicalLink= Down  
          Label= 10/100/1000 LAN1
        1:
          Interface= eth1
          Dot1x= None
          LogicalLink= Up
          PhysicalLink= Up 1000Mbps full
          Label= 100/1000/2500 PoE LAN2
      PoE Mode= Auto
      802.3af PoE Tx. chain= 2

LLDP:
             Status = Enabled
             Interval = 30
             HoldTime = 120
             Mgmt = Enabled
             Ports:
                Send out LLDP packet on eth0 = Enabled
                Send out LLDP packet on eth1 = Enabled
                Send out LLDP packet on eth2 = Enabled
                Send out LLDP packet on eth3 = Enabled
                Send out LLDP packet on eth4 = Enabled
                Send out LLDP packet on eth5 = Enabled

What I'm missing or doing wrong?

[hyosang_choi]

Hi.

Switch is allocated as 30W.

It works properly

You can confirm on Cli on the AP like below.

get power-mode

get lldp pse