cancel
Showing results for 
Search instead for 
Did you mean: 

packet Dropped issue on the port of ICX 7450 L3 switch

bharat_gole
New Contributor III

Hi Expert's,

we have facing packet lost issue on the one Port no 1/1/4 on ICX 7450 L3 Switch ,which we have connected Wi-Fi Zone Director 1200.

Please check log below and let us know how to resolved.

SW: Version 09.0.00T213

SSH@Quest_L3_SW_ICX7450# sh int eth 1/1/4
GigabitEthernet1/1/4 is up, line protocol is up
Port up for 3 hour(s) 25 minute(s) 42 second(s)
Hardware is GigabitEthernet, address is d4c1.9e2a.18d8 (bia d4c1.9e2a.18db)
Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx
Configured mdi mode AUTO, actual MDI
EEE Feature Disabled
Tagged member of 7 L2 VLANs, untagged in VLAN 98, port state is FORWARDING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0, mac-learning is enabled
MACsec is Disabled
Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is config enabled, oper enabled, negotiation disabled
Mirror disabled, Monitor disabled
Mac-notification is disabled
VLAN-Mapping is disabled
Not member of any active trunks
Not member of any configured trunks
Port name is ZoneDirector1200_Wi-Fi
IPG MII 96 bits-time, IPG GMII 96 bits-time
MTU 1500 bytes, encapsulation ethernet
MMU Mode is Store-and-forward
300 second input rate: 152336280 bits/sec, 24386 packets/sec, 15.63% utilization
300 second output rate: 148996192 bits/sec, 24347 packets/sec, 15.29% utilization
3254209714 packets input, 2511357944417 bytes, 0 no buffer
Received 2514096 broadcasts, 5901867 multicasts, 3245793965 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
3249586125 packets output, 2449719548623 bytes, 0 underruns
Transmitted 1194913 broadcasts, 1938515 multicasts, 3246452695 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
Protected: No
MAC Port Security: Disabled
Flexlink: Disabled

UC Egress queues:
Queue counters Queued packets Dropped Packets
0                          3244246967        10982623
1                          0                           0
2                          0                           0
3                          0                           0
4                          540676                 0
5                          4789                     0
6                          0                           0
7                         2605942                0


MC Egress queues:
Queue counters Queued packets Dropped Packets
0                          687017                0
1                          744940                0
2                          84882                  0
3                          671983                0

2 REPLIES 2

BenBeck
Moderator
Moderator

Hey @bharat_gole 

9.0 flat was pulled from the portal due to some major issues. Please upgrade to 9010d if you need 9.x, otherwise we would recommend 8095g. As for your actual issue, it looks like the egress queue 0 is being overrun. This could be due to many issues (bursty traffic, etc.). Realistically, I would recommend opening a case, so we can take a closer look (see my signature). You may be able to resolve this by playing with the egress buffers, but it is hard to say just off that output. See here for more information:

https://docs.commscope.com/bundle/fastiron-09010-trafficguide/page/GUID-FAC85D2C-9304-442F-8DB6-188E...

 

 

Ben Beck, RCNA, Principal Technical Support Engineer
support.ruckuswireless.com/contact-us

bharat_gole
New Contributor III

HI Benbeck,

Thanks for reply.

we already open this case. team is looking for that but no luck till now.

we want to 9.x Firmware because of IP DHCP binding scalability has been enhanced to support up to 3000 clients & 8.x not supported.

if you want the case number then i will share with you. Please let us know.