6450 stack w/8030n issues?
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-03-2018 08:43 AM
I'm working on setting up a 4 unit stack of ICX 6450-48s. Firmware installed is 8.0.3n - Routing. I am getting a continuous stream of the following entries to the console port:
T=17h5m20.1: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-up, ,
T=17h5m57.7: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-up, ,
T=17h7m59.8: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-dw, ,
T=17h8m9.4: 1/2/1 goes down. delete direction 0, trigger election
T=17h11m20.3: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-up, ,
T=17h13m56.9: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-dw, ,
T=17h17m9.5: 1/2/1 goes down. delete direction 0, trigger election
T=17h17m38.5: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-dw, ,
In addition the input errors and CRC numbers are steadily increasing.
I'm using the standard 1m stacking cables.
Does anyone know what might be happening? Is there a different version of firmware (earlier/later) that I should be using instead?
Any help is appreciated.
Todd
T=17h5m20.1: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-up, ,
T=17h5m57.7: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-up, ,
T=17h7m59.8: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-dw, ,
T=17h8m9.4: 1/2/1 goes down. delete direction 0, trigger election
T=17h11m20.3: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-up, ,
T=17h13m56.9: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-dw, ,
T=17h17m9.5: 1/2/1 goes down. delete direction 0, trigger election
T=17h17m38.5: Election, was active, no change, ID=1, pri=128, 4U(1-4), A=u1, nbr#=3 3, reason: u2: port-dw, ,
In addition the input errors and CRC numbers are steadily increasing.
I'm using the standard 1m stacking cables.
Does anyone know what might be happening? Is there a different version of firmware (earlier/later) that I should be using instead?
Any help is appreciated.
Todd
10 REPLIES 10
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2018 12:48 PM
Sorry for the delay. The cause was incorrect cables. I was inadvertently sent 1Gig stacking cables, not the required 10Gig. Surprising that the interfaces came up with the incorrect cables. Lots of errors, but still, I would not have expected the interfaces to still be active.

