can not connect ICX 7250-24 with Opendaylight oxygen controller

[nadir_shah]

Hello Everyone,
I have ICX 7250-24 switch and ODL oxygen version. I have connected the ethernet interface 1/1/1 to the  ODL controller. the controlling is running on ip address 192.168.2.25 port 8181. I have enabled the openflow ofv130 and have connected with controller using no ssl in Config mod. Then I enabled openflow layer23 on ethernet interface 1/1/1 with VLAN1  However, the switch is not getting connected with the controller. When I disabled openflow and assigned ip address to 1/1/1 ethernet interface, then the controller is pinged. However, it is necessary that the ip address should not be assigned to ethernet interface 1/1/1 if we want to enable the openflow. When the ip address is not assigned to the ethernet interface 1/1/1, then the switch cannot ping the controller. Can you help me in this regard?
thanks!
Nadir

[nadir_shah]

Hello Vu,
thanks for the reply, the pinging is done following the layer3 commands. However, when I connect to ODL controller using "openflow controller ip-address 192.168.2.25 no-ssl port 8181" it gives me error like "ERROR: Ctrl-1 in ver 1 sends pkt with hdr: ver 72 type 84 len 21584 xid 791752241
"

Can you help me that what is wrong? I have enabled send-to-controller default-behavior 

Looking forward for your guidance.
thanks!
Nadir

[nadir_shah]

i had the following commands
1. CS7250(config)#openflow enable ofv130
2. CS7250(config-if-e1000-1/1/1)#openflow enable layer23 hybrid-mode
3.CS7250(config)#openflow hello-reply disable
4. CS7250(config)#openflow controller ip-address 192.168.2.25 no-ssl port 8181
ERROR: Ctrl-1 in ver 4 sends pkt with hdr: ver 72 type 84 len 21584 xid 791752241
Bad Controller - teardown all connections!
CS7250(config)#

why is this error?
+++++++++++++++++++++++show run starts+++++++++++++++++++++++++++++
CS7250(config)#show running-config
Current configuration:
!
ver 08.0.80dT213
!
stack unit 1
  module 1 icx7250-24-port-management-module
  module 2 icx7250-sfp-plus-8port-80g-module
!
!
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 10 by port
 untagged ethe 1/1/1
 router-interface ve 10
!
vlan 250 by port
 tagged ethe 1/1/2
!
!
!
!
!
!
!
!
!
!
!
openflow enable ofv130
openflow hello-reply disable
openflow controller ip-address 192.168.2.25 no-ssl port 8181
!
!
aaa authentication web-server default local
aaa authentication login default local
boot sys tf 10.0.0.2 spz10111.bin
hostname CS7250
!
username admin password .....
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface management 1
 ip address 10.0.0.4 255.255.255.0
!
interface ethernet 1/1/1
 openflow enable layer23 hybrid-mode
!
interface ethernet 1/2/1
 speed-duplex 1000-full
!
interface ethernet 1/2/2
 speed-duplex 1000-full
!
interface ethernet 1/2/3
 speed-duplex 1000-full
!
interface ethernet 1/2/4
 speed-duplex 1000-full
!
interface ethernet 1/2/5
 speed-duplex 1000-full
!
interface ethernet 1/2/6
 speed-duplex 1000-full
!
interface ethernet 1/2/7
 speed-duplex 1000-full
!
interface ethernet 1/2/8
 speed-duplex 1000-full
!
interface ve 10
 ip address 192.168.2.26 255.255.255.0
!
!
!
!
!
!
!
!
!
!
end
CS7250(config)#

+++++++++++++++++++++++show run ends++++++++++++++++++++++++++++++

show open flow is follow
$$$$$$$$$$$$$$$$$$$$$$$$$$$ show openflow starts$$$$$$$$$$$$$$$$$$$

CS7250#show openflow
Administrative Status:       Enabled
SSL Status:                  Enabled
Controller Type:             ofv130
HELLO Reply:                 disabled
Number of Controllers:       1
Controller 1:
Connection Mode:       active, TCP
Controller Address:     192.168.2.25
Connection Port:       8181
Connection Status:      CLOSED
Role:                   EQUAL
Packet-in config:       no-match, action
Port-status config:     add, delete, modify
Flow-removed config:    delete, group-delete

Match Capability:
L2 : Port, SMAC, DMAC, Ether type, Vlan, Vlan PCP
L3 : Port, Vlan, Vlan PCP, Ethertype(IP,IPv6,ARP,LLDP), Source (IP/IPv6), Destination (IP/IPv6), IP Protocol, IP DSCP,
     TCP/UDP/SCTP(Src Port,Dst Port), ICMPv4/ICMPv6(Type,Code)
L23: Port, SMAC, DMAC, Vlan, Vlan PCP, Ethertype (IP,IPv6,ARP,LLDP), Destination (IP/IPv6), IP Protocol, IP DSCP,
     TCP/UDP/SCTP(Src Port,Dst Port), ICMPv4/ICMPv6(Type,Code)
Normal Openflow Enabled Ports:
Openflow Hybrid Interfaces:
e1/1/1
Protected VLANs   : None
Unprotected VLANs :    10,

Default action: drop
Maximum number of flows allowed: 3072
Active flow: 0
SLIB Switchover detected: YES
Maximum number of Protected Vlans allowed: 40
Maximum number of Unprotected Vlans allowed: 40
Total number of Protected Vlans: 0
Total number of Unprotected Vlans: 1

$$$$$$$$$$$$$$$$$$$$$$$$$$ show openflow ends$$$$$$$$$$$$$$$$$$$$$
looking forward for your help
thanks!
Nadir

[vu_pham_ghtztqm]

Hi Nadir - please try disable openflow on 1/1/1 if it is connected to the ODL server.

config t
interface ethernet 1/1/1
 no openflow enable layer23 hybrid-mode

write mem
exit

Let me know if it made any diff.

Thanks,

Vu

[nadir_shah]

it does not work
and the error is
--------------------------------------------------------------------------------
CS7250(config)#openflow controller ip-address 192.168.2.25 no-ssl port 8181

CS7250(config)#ERROR: Ctrl-1 in ver 4 sends pkt with hdr: ver 72 type 84 len 21584 xid 791752241
Bad Controller - teardown all connections!
---------------------------------------------------------------------------------------
on the server it is 
=========================================
$sudo netstat -an | grep 8181

tcp6   0   0  :::8181     :::*   LISTEN

tcp6   0   0  192.168.2.25:8181     192.168.2.26:7801   TIME_WAIT

=================================================

Please what is wrong?
Thanks!
Nadir

[vu_pham_ghtztqm]

HI Nadir - It seems like ICX is rejecting the ODL controller because it received an Openflow message with header version other than '100' or '130'. I would recommend open a support case so someone can help troubleshooting the issue further. It would help to have a wireshark capture the communication between ICX and ODL controller to verify.

Thanks,

Vu