cancel
Showing results for 
Search instead for 
Did you mean: 

icx7750 performance problem

andr_boucher_5j
New Contributor II
I have a icx7750 switch in a datacenter as routing device.  Everything was running fine, but since we merge with a new organization, response time of the switch is very bad (ssh lag in cli) and we are now losing communication randomly with some servers behind.  We added 4 access switch and 19 new router-interface ve (previously 2 switch and 49 interface ve).

cpu and memory dont seems to be a problem

can a system parameters was not set correctly (see below)?

thanks

SSH@R0202000-DISTR-CT-RT-01#sh default values
sys log buffers:50         mac age time:300 sec       telnet sessions:5

ip arp age:10 min          bootp relay max hops:4     ip ttl:64 hops
ip addr per intf:24

when multicast enabled :
igmp group memb.:260 sec   igmp query:125 sec         hardware drop: enabled

when ospf enabled :
ospf dead:40 sec           ospf hello:10 sec          ospf retrans:5 sec
ospf transit delay:1 sec

when bgp enabled :
bgp local pref.:100        bgp keep alive:60 sec      bgp hold:180 sec
bgp metric:10              bgp local as:1             bgp cluster id:0
bgp ext. distance:20       bgp int. distance:200      bgp local distance:200

System Parameters    Default    Maximum    Current    Configured
ip-arp               8192       64000      8192       8192
ip-static-arp        512        1024       512        512
ip-cache             8192       32768      8192       8192
ip-filter-port       2047       2047       2047       2047
ip-filter-sys        3072       8192       8192       8192
l3-vlan              32         1024       32         32
ip-qos-session       1024       16000      1024       2048
mac                  32768      32768      32768      32768
ip-route             98304      131072     98304      98304
ip-static-route      64         2048       64         64
vlan                 64         4095       1024       1024
spanning-tree        128        254        128        128
mac-filter-port      32         256        32         32
mac-filter-sys       64         512        64         64
ip-subnet-port       24         128        24         24
session-limit        65536      160000     65536      65536
view                 10         65535      10         10
virtual-interface    255        512        255        255
hw-ip-next-hop       17408      17408      17408      17408
hw-traffic-condition 50         1024       50         50
rmon-entries         2048       32768      2048       2048
igmp-snoop-mcache    512        6144       512        512
mld-snoop-mcache     512        6144       512        512
ip6-route            5120       7168       5120       5120
ip6-static-route     64         1024       64         64
ip6-cache            1024       2048       1024       1024
msdp-sa-cache        4096       8192       4096       4096
gre-tunnels          16         64         16         16
ip-vrf               128        128        128        128
ip-route-default-vrf 65536      131072     8000       8000
ip6-route-default-vr 2048       7168       2048       2048
ip-route-vrf         4096       131072     4096       4000
ip6-route-vrf        1024       7168       1024       1024
pim-hw-mcache        1024       6144       1024       1024
pim6-hw-mcache       512        2048       512        512
igmp-snoop-group-add 4096       8192       4096       4096
mld-snoop-group-addr 4096       8192       4096       4096
mac-notification-buf 4000       16000      4000       4000
openflow-flow-entrie 3072       3072       3072       3072
openflow-pvlan-entri 40         40         40         40
openflow-unprotected 40         40         40         40
max-ecmp             8          32         8          8
max-dhcp-snoop-entri 1024       3072       1024       1024
max-static-inspect-a 512        1024       512        512
7 REPLIES 7

jles
New Contributor II
Have you tried enable loop detection to see if there is a loop or something like that? 

andr_boucher_5j
New Contributor II
no clues in the logs, cpu/memory in deep sleep, no loop by the way

SSH@R0202000-DISTR-CT-RT-01#sh cpu-utilization
1 percent busy, from 12549 sec ago
1   sec avg:  1 percent busy
5   sec avg:  1 percent busy
60  sec avg:  2 percent busy
300 sec avg:  1 percent busy

I plan to mode some int VE elsewhere and monitor the whole thing.  Next step will be to open a case I think

thanks

louis_torrez
New Contributor
Hello,

Any luck on this, I have very similiar issue.

Thanks.