ICX6430-c12 connection/setup issue

[gtomkins46]

I purchased a used ICX6430-C12.  Said it was factory reset.  I have been trying to go through the initial setup with putty using a usb to serial cable, then the flat blue console cable from a cisco firewall.  The putty screen connects and I can see all the boot information going on.  When it asks me to press "b" I can see my transmit light go on and the 0 turns to a 1 then back to 0.

The switch then continues to boot until it gets stuck at a point and I cannot do anything inside of the putty screen.  I have pasted the boot information below.  Where it ends is where the device gets stuck and just sits.  I have also tried to physically factory reset by pressing and holding the reset button at power up, however no lights come on even after holding it for a minute.  As soon as I let go of the button it boots up.

Boot information below:

Bootloader Version: 08.0.00T310 (Apr 24 2013 - 17:31:15)


Model ID: 0.0.0.0.0.1

Enter 'b' to stop at boot monitor:  0
bootdelay: ===
Booting image from Primary
## Booting image at 00007fc0 ...
   Created:      2015-11-04   5:45:39 UTC
   Data Size:    8485960 Bytes =  8.1 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel in BE mode ...
Uncompressing Image.................................................................................................................................................................................................................................................................................................................................................................... done, booting the kernel.
IP-Config: Gateway not on directly connected network.
Config partition mounted.
Creating TUN device
Starting the FastIron.
FIPS Disabled:PORT NOT DISABLED
platform type 48
OS>Unable to set the kernel wall time
                                      Starting Main Task .INFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
CPSS DxCh Version: cpss3.4p1 release
Pre Parsing Config Data ...
INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also

Parsing Config Data ...
INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also

System initialization completed...console going online.
  Copyright (c) 1996-2015 Brocade Communications Systems, Inc. All rights reserved.
    UNIT 1: compiled on Nov  3 2015 at 21:43:36 labeled as ICX64S08030d
                (8486536 bytes) from Primary ICX64S08030d-BNA-66283.bin
        SW: Version 08.0.30dT311
  Boot-Monitor Image size = 779020, Version:08.0.00T310 (kxz08000)
  HW: Stackable ICX6430-C12
==========================================================================
UNIT 1: SL 1: ICX6430C 12-port Management Module
         Serial  #: CPW0422J03P
         License: BASE_SOFT_PACKAGE   (LID: eryFJHHlFIr)
         P-ENGINE  0: type E7EE, rev 01
==========================================================================
UNIT 1: SL 2: ICX6430C-Copper 2port 2G Module
==========================================================================
UNIT 1: SL 3: ICX6430C-Fiber 2port 2G Module
==========================================================================
  500 MHz ARM processor ARMv5TE, 400 MHz bus
32768 KB flash memory
  256 MB DRAM
STACKID 1  system uptime is 6 second(s)
The system : started=cold start

ICX6430-C12 Switch>
Stack unit 1 PS 1, Internal Power supply detected and up.

Stack unit 1 PS 1, Internal Power supply detected and up.
PoE: Stack unit 1 PS 1, Internal Power supply  with 68000 mwatts capacity is up
PoE Info: Adding new 54V capacity of 68000 mW, total capacity is 68000, total free capacity is 68000
PoE Info: PoE module 1 of Unit 1 on ports 1/1/1 to 1/1/4 detected. Initializing....
PoE Event Trace Log Buffer for 2000 log entries allocated
PoE Event Trace Logging enabled...
PoE Info: PoE module 1 of Unit 1 initialization is done.

[aalvarez6]

Hello, 

While you are in boot mode, try the following commands: boot_primary or boot_secondary. If that fails, try a software recovery. Here is the upgrade guide. Filter by "boot" or "software recovery"
https://support.ruckuswireless.com/documents/1496-fastiron-08-0-01-software-upgrade-guide

Regards, 

Ayleth Alvarez