Showing results for 
Search instead for 
Did you mean: 

How to put ZF R710 in 802.3at PoE+ Mode?

Contributor III
Hi, I have an issue where I am unable to put my new ZF R710 into 802.3at PoE+ Mode.  Currently, I have a new POE+ switch that I'm using which is the Linksys LGS308P. It has LLDP enabled on the switch end. Note, my ZF R710 is in standalone mode.  Is there any other configuration that I need to do either on the Linksys LGS308P or ZF R710 so I can out it into   802.3at PoE+ Mode?

Esteemed Contributor II
KBA-5005 has the following information, including two CLI commands for the AP, if your switches have LACP/LLDP enabled.

Root Cause
Image_ images_messages_5f91c428135b77e24798fd60_be7ae6d9de84f27ee81a60ec08916f9a_info16-0943f36f-669c-46ee-a9e6-8ddb2575ca40-1849708274.png
and LLDP power over MDI should be enabled on the POE+ switch in order
for 802.3at power to be negotiated between the R710 and POE+ switch.

Troubleshooting Steps
Image_ images_messages_5f91c428135b77e24798fd60_be7ae6d9de84f27ee81a60ec08916f9a_info16-0943f36f-669c-46ee-a9e6-8ddb2575ca40-1849708274.png
Use rkscli command "get power-mode" to check input power consumption status.
rkscli: get power-mode
PoE Configured Mode      : Auto
Power Consumption Status : 802.3at PoE+
"PoE Configured Mode" should be "Auto" not "AF".
When PoE+ switch with LLDP power via MDI support is connected, the " Power Consumption Status" will be "802.3at PoE+".
Here are options for " Power Consumption Status".
    { "Unknown"      },
    { "DC"           },
    { "802.3at PoE+" },
    { "PoE Injector" },
    { "802.3af PoE"  },

Image_ images_messages_5f91c428135b77e24798fd60_be7ae6d9de84f27ee81a60ec08916f9a_info16-0943f36f-669c-46ee-a9e6-8ddb2575ca40-1849708274.png

Image_ images_messages_5f91c428135b77e24798fd60_be7ae6d9de84f27ee81a60ec08916f9a_info16-0943f36f-669c-46ee-a9e6-8ddb2575ca40-1849708274.png
There are 3 requirements for the R710s to negotiate 802.3at power between itself and the POE+ switch,
two of them are on the POE+ switches and one on the Ruckus R710-:

1. LLDP must be enabled on the POE+ switches.

2. LLDP Power via MDI must be enabled on the POE+ switches.
The command to enable LLDP and LLDP power via MDI will vary depending on the make of the switch.

LLDP and LLDP POE setting must be enabled on the R710s. R710s received
with have both LLDP and LLDP POE setting ENABLED by

However, R710s received with firmware prior to DON'T have LLDP and LLDP POE setting enabled by default.
These settings WON'T be enabled even after upgrading to or RuckOS 3.1.1.x.x or later.

if R710s received with firmware prior to, then later
upgraded to or 3.1.1.x.x, still need to have LLDP and LLDP
POE enabled.
This can be done via CLI on the R710.

rkscli: set lldp enable
rkscli: set lldp poe enable

You can do a get lldp to make sure the ap took the two config changes.

rkscli: get lldp
LLDP state: Enabled
LLDP interval: 30
LLDP holdtime: 120
LLDP mgmt: Enabled
LLDP poe: Enabled
LLDP power: 25000
LLDP interface:
LLDP on eth0 : Enabled
LLDP on eth1 : Enabled

PS: Negotiation may take up to 2 minutes after system is up.

Customers report success after following this example on Juniper switches:

Hey Michael, with all the trouble that's been reported with getting the R710 into AT power mode, do you think Ruckus Marketing can change the Datasheet of the R710  stating that to put it into AT Mode requires LLDP via MDI Support on the switch.  The Datasheet is very miss leading thinking if you have a POE+ switch that it would work in AT Mode, This is my biggest complaint.  This would prevent people from getting the wrong hardware in the first place. 

New Contributor
oddly enough I cannot get this AP to negotiate in poe+ after rebooting the ap the lldp settings go back to disabled and need to be re-enabled.

they are on v 9.12 controlled by a zd 1200 switch is a sg300-28pp, all settings look good for lldp and they are Lagged on the switch.

I have the same issue.  Settings do not survive a reboot.