cancel
Showing results for 
Search instead for 
Did you mean: 

Need OID for number of clients connected to one AP

jerry_heath_adk
New Contributor III
I am using a third party software application which provides a way for SNMP polling to return the number of clients associated with each Autonomous Ruckus AP (Zoneflex indoor 7352's and 7372's).  On the home screen, all the AP's are listed with the number of current connections next to it.  This is accomplished by entering the custom OID in the software's setup for each AP along with the community string. This works fine for the Cisco AP's using the OID of 1.3.6.1.4.1.9.9.273.1.2.1.1.18 .  So far, I have tried these OID's for the Ruckus AP's:

.3.6.1.4.1.9.9.273.1.1.2
1.3.6.1.4.1.25053.1.2.1.1.1.15.2
1.3.6.1.4.1.25053.1.2.2.1.1.2.1.1.15
1.3.6.1.4.1.25053.1.2.2.1.1.1.1.1.30
1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.3.21
.1.3.6.1.4.1.25053.1.1.12.1.1.1.3.1.2

None of these OID's work for me.  Any suggestions will be appreciated.  I am using SNMP v2c on the Ruckus AP's without the inclusion of a Zone Director, only the third party software running on its router/controller.
18 REPLIES 18

jerry_heath_adk
New Contributor III
Todd and Matt,
Do you think I should include the first dot as in:

.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.3.6

or leave it out as in:

1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.3.6

or does it matter?

jerry_heath_adk
New Contributor III
So I did an snmp walk today on my stubborn Ruckus ZF7352.  The walk returned a long list of OID's (the total at end of list indicated 2878 but, actually, there were only 295 listed).  Interestingly, the list started with .1.3.6.1.4.1.25053.1.1.12.1.1.1.3.1.11.1 , which is very close to the OID sent by Todd, 1.3.6.1.4.1.25053.1.1.12.1.1.1.3.1.2.1 .  None of the OID's returned by the walk had a value that was within 1 of the actual number of associated clients on the AP in question.  I am not sure why Todd's OID wasn't included in the list.  The walk command I used was "snmpwalk.exe -r:192.168.0.55 -v:2c"  Did I do something wrong?

Sorry was on vacation last week.   Just when I think I'm getting a grasp on this SNMP stuff, something like this happens and makes me think I know nothing.  Your command is exactly the same as mine so I don't think you did anything wrong.

Sorry I cannot be of more help.... I would have thought that "walk" would have returned the info you needed.

Jerry,
You could also use the Paessler MIB Importer to try to find your OID.  It provides a a description for each MIB.

Image_ images_messages_5f91c466135b77e247a5f919_3d796278b296ee96cedad43620d1afb8_RackMultipart201612021146431e2-0ee8f2f4-cb7a-4348-bea7-7f8e1b4b5060-366568209.jpg1480694461