R650 - max download 500ish? Unleashed

[silicondt]

We bought and installed some R650. I cannot seem to get the download over 500mb. The upload goes to 920ish.

The internet itself is not the problem. I can hook a laptop with ethernet up to the "second" port on the R650 and pull 950/950.

I have tried every combination of channels at 80hz 5ghz. We have tried this at multiple locations also. (office, home, office 2) . I cannot pull over 500mb on the download only using speedtest.net

I am sitting 5-10ft away from the AP with clean line of site... I even tried lowering the power.

When I do IPERF tests it sort of reflects this also. Maybe a little higher on download (600-650) But the upload it max at 1gb(ish) speeds....

I have it manually set to 802AT and it does not complain about the power - but also noticed it never goes above 8-9watts. Why does it NEED 802AT yet never even go over 15 watts? hmm

[Ayush_Tripathi]

Hello,

1) Could you please confirm the LAN speed in your network and share the result of the iPerf test, which you have performed?

2) Also, confirm which type of client device you are using for the speed test. If it is a Windows device, please share the output of the command below from the Windows CMD.

#netsh wlan show interfaces

3) When you are doing the speed test, please confirm how many clients are connected to the AP.

4) From the AP CLI, please share the output of the command below

#get eth

#get power-mode

[silicondt]

There is 1 interface on the system:

Name : Wi-Fi 2
Description : Intel(R) Wi-Fi 6 AX200 160MHz
GUID : faf18b7a-5093-4cba-a438-720bb62c4f4c
Physical address : 0c:91:92:50:b6:35
State : connected
SSID : test2
BSSID : 74:31:7e:97:93:40
Network type : Infrastructure
Radio type : 802.11ax
Authentication : WPA2-Personal
Cipher : CCMP
Connection mode : Profile
Channel : 40
Receive rate (Mbps) : 1201
Transmit rate (Mbps) : 1201
Signal : 99%
Profile : test2

Hosted network status : Not available

Copyright(C) 2026 Ruckus Wireless, Inc. All Rights Reserved.

** Ruckus R650 Multimedia Hotzone Wireless AP: 442551001620

rkscli: get eth

Port Interface 802.1X Logical Link Physical Link Label
-----------------------------------------------------------------
0 eth0 None Down Down 10/100/1000
1 eth1 None Up Up 1000Mbps full 10/100/1000/2500 PoE

Note: Read Port#N as N+1, if you are referring this CLI output with AP's "Configure :: Ethernet Ports" UI Page.
OK
rkscli: get power-mode
PoE Configured Mode : Auto
Power Consumption Status : PoE Injector
USB Status : Enabled
rkscli:

There is 1 interface on the system:

Name : Wi-Fi 2
Description : Intel(R) Wi-Fi 6 AX200 160MHz
GUID : faf18b7a-5093-4cba-a438-720bb62c4f4c
Physical address : 0c:91:92:50:b6:35
State : connected
SSID : test2
BSSID : 74:31:7e:97:93:40
Network type : Infrastructure
Radio type : 802.11ax
Authentication : WPA2-Personal
Cipher : CCMP
Connection mode : Profile
Channel : 40
Receive rate (Mbps) : 1201
Transmit rate (Mbps) : 1201
Signal : 99%
Profile : test2

Hosted network status : Not available

[silicondt]

1) Could you please confirm the LAN speed in your network and share the result of the iPerf test, which you have performed?

The lan speed is 1gb 1gb over online speed tests. I have verified this by connecting a laptop to the secondary port of the R650 and do a speed test..

2) Also, confirm which type of client device you are using for the speed test. If it is a Windows device, please share the output of the command below from the Windows CMD.

I have used about 10 devices.. Iphone 5 pro Iphone 6 pro, Andriod, laptop.. all the same. Download is like 500-600 max and upload is always around 950ish

3) When you are doing the speed test, please confirm how many clients are connected to the AP.

Just 1 while we are testing.