Unable to connect to newly created Network
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-05-2019 06:35 PM
Ruckus Unleashed 510.
I went to through the popup screen to set up my new Ruckus AP and after setup there is an authentication failure that would not let me connect to the new created wireless network.
I already tried the hard factory reset and it does not go to the Configure-me-xxxx screen, it still recognizes the wireless network I created.
How can I reset my password?
How can I revert the AP to go back to "Configure-me-xxx" wireless network so I can attempt another set up using the app?
I went to through the popup screen to set up my new Ruckus AP and after setup there is an authentication failure that would not let me connect to the new created wireless network.
I already tried the hard factory reset and it does not go to the Configure-me-xxxx screen, it still recognizes the wireless network I created.
How can I reset my password?
How can I revert the AP to go back to "Configure-me-xxx" wireless network so I can attempt another set up using the app?
3 REPLIES 3
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-07-2019 11:34 AM
Hi Merone,
Are you connecting to your Unleashed AP via an ethernet cable? This my be easier for the initial configuration if you are having issues connecting wirelessly.
In order to perform a factory default on the AP, you need to hold in the reset button by the Ethernet port for at least 20 seconds.
Further support and documentation can be found at: https://support.ruckuswireless.com/product_families/19-ruckus-unleashed
I hope that helps,
Darrel.
Are you connecting to your Unleashed AP via an ethernet cable? This my be easier for the initial configuration if you are having issues connecting wirelessly.
In order to perform a factory default on the AP, you need to hold in the reset button by the Ethernet port for at least 20 seconds.
Further support and documentation can be found at: https://support.ruckuswireless.com/product_families/19-ruckus-unleashed
I hope that helps,
Darrel.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-08-2019 10:57 AM
Hi Darrel,
Yes, the AP is being connected via an Ethernet cable. I have already tried the hard reset and am not getting the AP to revert to factory default settings.
Can you please advise how I can reset the password for the created network? Or other solutions to get the brand new AP working?
I'm at the very beginning stages in trying to connect this.
Yes, the AP is being connected via an Ethernet cable. I have already tried the hard reset and am not getting the AP to revert to factory default settings.
Can you please advise how I can reset the password for the created network? Or other solutions to get the brand new AP working?
I'm at the very beginning stages in trying to connect this.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-09-2019 12:58 AM
Hi Merone,
Apologies it looks like you need to be connected to the setup SSID - please see further assistance here: https://support.ruckuswireless.com/articles/000005204
And a similar issue to yours reported here (where the above link is): https://forums.ruckuswireless.com/ruckuswireless/topics/default-super-password-after-factory-reset-f...
I hope this helps,
Darrel.
Apologies it looks like you need to be connected to the setup SSID - please see further assistance here: https://support.ruckuswireless.com/articles/000005204
And a similar issue to yours reported here (where the above link is): https://forums.ruckuswireless.com/ruckuswireless/topics/default-super-password-after-factory-reset-f...
I hope this helps,
Darrel.