cancel
Showing results for 
Search instead for 
Did you mean: 

R300 + Draytek 2925 Multiple SSIDs, VLANs, island SSID and failed internet connection

erik_kerstjens
New Contributor
Hey all,

This is the first time I'm working with VLANs and stuff so forgive me my noobness 🙂

The situation:
I got a Ruckus R300 AP connected on port1 to a Draytek Vigor 2925 (non WiFi version). The Draytek is connected to my internet cable modem which has IP 192.168.0.1 and DHCP enabled.
For the DrayTek and Ruckus R300 settings check the images below.

What I would like:
Create 3 SSIDs with a different seperated network for each SSID; 2 password protected and 1 open for guests

What I got working:
Well basically after hours of trial & error I got everything working except for the internet status connection on my R300 that says (disconnected) which I think leads to the R300 sending out an "island-XXXXXX" SSID. From my Google experience this is because the R300 can't access the gateway or is still in factory default mode. As you can see in the following image the Connection Status is down.

Image_ images_messages_5f91c3e6135b77e2478d306d_aa4da00f85d5421e5b1dddbff022fa7d_RackMultipart2015072748541lri1-e57b41ae-346f-415c-9681-39b9de35c2d7-937773722.png1438025133
Internet connection settings on the R300:
Image_ images_messages_5f91c3e6135b77e2478d306d_b0331e7afeb288472ba02e7b11145b1f_RackMultipart2015072716908idpq-8869a722-4481-453d-bfc1-a509d06fbcfc-1713107864.png1438025318
Local Subnet1 on R300:
Image_ images_messages_5f91c3e6135b77e2478d306d_5604e1d1c8f2a6dc2c6b3bbf9569f4db_RackMultipart201507271911zqk8s-4c789c86-e768-442e-815d-e91343af7ca7-1217254419.png1438025366
Local Subnet2 on R300:
Image_ images_messages_5f91c3e6135b77e2478d306d_a020d16e1d8d3abfa27751c325ffd961_RackMultipart2015072716409anlf-794b54c6-baa1-4605-935c-92bae978a96e-1631202458.png1438025417
Local Subnet3 on R300:
Image_ images_messages_5f91c3e6135b77e2478d306d_157373caf84583dcd89baf21df63fb35_RackMultipart20150727322071cgh-ea31fd36-dcfa-4324-8540-3e7af7cde2d5-1854182756.png1438025436
VLAN Configuration on Draytek Vigor 2925
Image_ images_messages_5f91c3e6135b77e2478d306d_5ad6149c298f97de63f906c5cf47feb8_RackMultipart2015072714945186e-569b80b1-09b2-4749-9923-8a9854e5ba3e-959113218.png1438025487

LAN General Setup on Draytek Vigor 2925
Image_ images_messages_5f91c3e6135b77e2478d306d_18e3d51085cfc3c7e93a161cbbc6ef2b_RackMultipart20150727191114rtq-d66d0998-8d19-43c5-9c42-27a10b10f85c-1496006123.png1438025563

Details Page LAN1 from above image:

Image_ images_messages_5f91c3e6135b77e2478d306d_41d851d3fb6a1e7a2bd0714cd6d58b02_RackMultipart20150727286802w58-db181e23-638b-4501-8ba1-c092c2c81df8-694136091.png1438025616
Details Page LAN2:
Image_ images_messages_5f91c3e6135b77e2478d306d_47f4938d79f9daced44befc9f7705ef1_RackMultipart201507271564c5v3z-531a1fd1-d4fc-477e-b661-7f0ff95e8118-157382450.png1438025660
Details Page LAN3:
Image_ images_messages_5f91c3e6135b77e2478d306d_dca619dc9a644965853401f16e4502f5_RackMultipart2015072729557ay6t-172d5f71-42a5-40df-83e3-e23053649f88-906727333.png1438025697

These are the WiFi settings for the guest network on the R300.
I named the WiFi networks according to the VLANs to make things a bit easier. to remember. So the VLAN10 network is set to Local Subnet 1, VLAN20 to Local Subnet 2 (see image below) and VLAN30 to Local Subnet 3.
Image_ images_messages_5f91c3e6135b77e2478d306d_ba04ae266df1f5967c7fd8b2b774f96f_RackMultipart20150727256581f5e-623a2856-081e-4581-a0d0-2f49aea878e7-1528904012.png1438025797

So everything is working just fine but I have a feeling I have missed a few steps. I tried disabling the "island-XXXXXX" by logging in to the R300 via SSH and perform the following CLI commands:

set state wlan102 down
set state wlan103 down

This works however, after I powercycle the R300 the "island" SSID pops up again.
Sorry for the long post, if there is any more information you need please let me know.

Thanks in advance for your support!
1 REPLY 1

raymond_brink
New Contributor
Hey you've been working? I have the same problem