-
Does it support PIM routing at router-only interface on ICX?
Hi, I tested PIM (Dense Mode and Sparse Mode) on an ICX switch(10010g_cd6) The multicast source is located on interface ve 1 (e 1/1/1), and the receiver is connected to another L3 switch via interface e 1/3/4 (configured as route-only / untagged VLAN 4000). I noticed that the receiver does not receive the traffic when the…
-
ICX-7750 CPU high
We have been experiencing intermittent high CPU utilization and wireless AP disconnections on our ICX7550-24F stack for several months. Device Information Model: ICX7550-24F (Stack) FastIron Version: 08.0.95sT243 Uptime: Approximately 153 days Issue Summary CPU utilization increases during school hours (approximately…
-
ICX7150-C12P will not boot — NAND/ECC errors and network recovery failing
I have been trying for a few hours with ChatGpt to get the Ruckus working again. I think it has been offline for several years probably when a wifi router changed but who knows really. Here is where we left off after I gave up. I have an ICX7150-C12P that no longer boots normally. Power LED is green and SYST LED is solid…
-
"spanning-tree 802-1w admin-edge-port" and "fast port-span"
Hi expert, I've been looking into the commands: -(config)#fast port-span -(config-if-e1000-1/1/1)#spanning-tree 802-1w admin-edge-port I'm not sure if applying both configurations on the edge ports is recommended. My network works with 802.1w and my switches are ICX8200 (FastIron 10).
-
Trying to upgrade ICX 7150X
https://support.ruckuswireless.com/software_terms_and_conditions/2463-ruckus-icx-fastiron-08-0-80f-ga-software-release-zip https://support.ruckuswireless.com/software_terms_and_conditions/3409-ruckus-icx-fastiron-08-0-95g-ga-software-release-zip…
-
ICX7150 – DHCPv6 Prefix Delegation Client and Dynamic IPv6 Prefix Assignment
I have already contacted RUCKUS Support regarding this question. Unfortunately, technical assistance requires an active support contract. Before considering additional network hardware, I would like to confirm whether the required functionality is actually supported by the ICX7150. I am not asking for a complete…
-
I am unable to log in to my Ruckus account
I saw a similar post from last week where the customer could also not log in to the app or online. What is the website we are to use to log in with the credential provided?
-
uplinking icx8200 to fortinet
so, i have existing ICX8200’s in this infrastructure and older ICX6450’s. we’re replacing the 6450’s with 124F-FPOE switches, but i’m having trouble getting the 124’s to talk to the 8200’s. the 124’s are running 8.0.0(47). the 124’s will uplink to the 6450’s with no trouble, but will not pass traffic to/from the 8200’s.…
-
ICX7150 & ICX7450 recomeneded version
Hi All, Good Day..! Anyone please share the suggested stable relase version for ICX7150 & ICX7450
-
snStackingOperUnitDescription OID values
Hi, Could you provide the complete list of possible values returned by SNMP OID 1.3.6.1.4.1.1991.1.1.3.31.2.2.1.6 (snStackingOperUnitDescription ) on ICX7650 with FastIron 09.x? The MIB defines it as a DisplayString, but we need all possible status strings for monitoring. Thanks, Volodymyr
-
ICX7150 both flash partitions corrupted — need SPR08080f.bin for boot monitor recovery
My Ruckus ICX7150 is stuck in a boot loop with both primary and secondary flash partitions corrupted. I am at the boot monitor prompt (ICX7150-Boot>). Boot monitor version is 10.1.15T225 which cannot accept UFI images — I need the intermediate non-UFI SPR08080f.bin and mnz10114.bin to recover. The Ruckus support portal is…
-
ICX8000 SCP Backup Creates 0-Byte Files on QNAP Server
Hello Ruckus Support Team, I am experiencing an issue when attempting to back up the running-configuration from ICX8200 switches to a QNAP server using SCP. copy running-config scp 10.x.x.x /QNAP/S1-Core-MDF.cfg The switch initiates the transfer, but the process takes an unusually long time and ultimately creates a backup…
-
Point-to-Point between 2 locations
We installed a point-to-point connection between our data center and one of our branch locations. One connection is 10g and goes straight into an ICX750 with a1310nm SFP connector and port configured for 10g-full. The other end goes into a Ciena 10g with a tunable SFP connector. It comes out of the Ciena with a 1g copper…
-
How to use the packet-capture command
Hi everyone, I'm trying to use the packet-capture remote command on an ICX 7550 switch, but every time I enable it, I receive the following message: Please configure remote IP address before enabling remote packet capture I've searched through the CLI help, configuration guides, and various documentation, but I haven't…
-
What do the different MAC Event Actions mean?
I'm trying to find documentation on what each of the MAC Event actions mean in the logs and I can't find it. Here is an example log entry: May 15 07:45:27 MA_MDF MAC-Event: MAC:aaaa.aaaa.aaaa-VLAN:511-PORT:2/1/48-ACT:1:: I'm guessing Action 1 is MAC registration but can anyone point me to where these actions are defined?
-
OSPF LSA Issue ICX7150
Model - ICX7150-C12-2X10GR Version - 08.0.95rT213 Each time a single port withing a vlan changes operational state, the VE initiates an LSA removal form the tree at the same time that it adds the LSA to the tree. This happens simultaneously and if there is an interface flapping due to a damaged cable, it creates excessive…
-
Update Datasheets of ICX8200-48NP2-E2-G & ICX8200-48NP2-E2-G
Dear All, Could someone assist in updating datasheets of ICX8200-48NP2-E2-G & ICX8200-48NP2-E2-G on support site or on the Ruckus Web-Site. The switch was announced on 7/4/2026. --Thanks
-
C08-ZP Switching Capacity?
What is the actual switching capacity of the C08-ZP? It says 56 Gb/s in the product specifications but in the Ruckus model feature comparison sheet it says 200 Gb/s.
-
ICX6430-c12 connection/setup issue
I purchased a used ICX6430-C12. Said it was factory reset. I have been trying to go through the initial setup with putty using a usb to serial cable, then the flat blue console cable from a cisco firewall. The putty screen connects and I can see all the boot information going on. When it asks me to press "b" I can see my…
-
Nand erase removed packages and files from resources and config mtds!
An AI agent decided that a nand erase would solve my switch problem when I bought a used switch and needed to erase the old users and passwords so I could log in. So I, of course, blindly followed its instructions in the middle of the night. I have recovered using some interesting extracts from the Ruckus image file, a…
-
Faulty SFP ports?
Hi, we have an issue with 1/3/2 and 1/3/4 SFP ports of the a Ruckus ICX 7150 switch. These SFP ports are used with 3x SFP adapters for fiber cables. According to our tests (we tried to replace and swap SFP adapters, fibers and the switch at the other end) the issue is related to these two specific ports. If we move the SFP…
-
G and H firmware?
There was an H firmware released a few days ago but now a G_cd7 released today. Is there an issue with the H? What's the deal with the seaming "downgraded" firmware release?
-
difference between qos profile and qos schedule-profile?
HI. What is the difference between qos profile and qos schedule-profile? I think both are same as allocation of bandwidth. Anyone let me know about it? Thanks.
-
ICX7450 lost IP address after firmware update to 08.0.30h and serial console shows no signs of life
Hi, I've upgraded the firmware of our ICX7450-24P (primary image) and after reboot the switch works normally but it is no longer reachable at his IP address. The serial console shows no signs of life after connecting to it with a Wirenest Console Cable (for use with ICX7250, ICX7450 ICX7750 Switches aftermarket replacement…
-
Trying to upgrade ICX7850 to TNR10010g_cd6ufi.bin from 08.0.92dT233
Hi, As the title above mentioned, I've been facing issues upgrade via USB and TFTP and show error. For USB, the error is as below. Application image alone download is not allowed in ICX7850 platform Please try downloading UFI image For TFTP, the error code is shown TFTP to Flash Error - code 5
-
Installing Firmware with FTP with BusyBox
Ive been trying to get my a couple ICX 6450-64P switches to work. I found a detailed approach suggested on Reddit that about 5 year old. https://www.reddit.com/r/Brocade/comments/dwglj7/web_interface_on_icx_643024p_only_shows_front/ it Recommends firmware version 08.0.30sa and I tried it, and many others, in a lengthy…
-
ICX 7550 UFI Firmware upgrade via TFTP Failing - Code 17
I am attempting a firmware upgrade of my ICX 7550 L3 switch stack via TFTP. From Version 08.0.95fc to 10.0.1g (stability release). When attempting to copy from the TFTP, I am getting persistent timeout errors on the TFTP server and eventual failure on the switch side. I have set up a PC as a TFTP server (10.17.2.100) and…
-
How to get firmware for my ICX-6430-24P Switches?
'Ruckus is great on AP firmware. Why can I find a complete download for the Ruckus ICX 6430-24P
-
Procedure how to upgrade ICX 7150 24P from version 08.0.92 to most recent one
Hi everyone, is there any specific procedure I have to follow to update my switch to version 10? Or can I go directly to the latest greatest? Current running version is 08.0.92T211. Thanks!
-
Does anyone know why I'm getting this message on an ICX switch?
Hi Team. I'm trying to configure IPPM for testing, but I'm getting the following error when I try to ping, and it's failing. Does anyone know why this is happening? Too many pings in progress, can't ping now Model : 7850-48F, FW version : TNR10020b_cd4 How shoud I resolve it? Regards.