nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

I had power fluctuations few times and switch isn't working properly since then (very slow & drops)

rahulmandava

I had power trips and fluctuations yesterday 4-5 times. Since then switch is not working properly. Internet is very slow and connection drops intermittently. Tried restarting modem, router and switch no use still the same.

My setup : Modem -> Wifi Router -> Ruckus switch -> zoning points one in each floor.

Any help is much appreciated!!

Find more posts tagged with

Accepted answers

imran.sanadi@commscope.com

Hi @rahulmandava

Greetings!!!

Thank you for the response and the information you shared.

This issue is because your switch is running on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. Due to a power outage/power spike, the Switch boots up on the other partition which may be running on a ‘Routing Code’ results in causing this issue.

As I can see from the output you shared, your Switch is booted up on the secondary partition which is running on Routing code (SPR) as highlighted in the below screenshot.

Please Enter the below commands in CLI to fix this issue:

Note: Hit Enter to accept each command

enable

copy flash flash secondary

boot system flash secondary yes

Example:

VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc

ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished)
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

Please let me know if you have any queries in this regard.

NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS if your issue gets resolved.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

All comments

Deepu

Hi ,

Greetings!

I understand that there was a power fluctuations few times and after that switch is slow and drop pakets

Please help us with the below information

-Do you see any amber light indication on the switch ?
-what is the current firmware version ?
-check if there is a CPU spike on the switch
#Show cpu(5 times)
#Show cpu task(3 times)

-share us with the above output .

Regards ,

Deepu Sekar

rahulmandava

Hi Deepu,

Thanks for getting back to me. I am not seeing any amber light on switch, just the regular light that we always see.

Regarding the firmware and cpu spike info, I am not sure how to check those. I am not able to connect or login to switch. Could you please help me with the steps on how I can get there ? or any other ways to resolve the issue ?

Deepu

Hi Rahulmandava ,

Than you for your response , I understand that . you are not able to connect or login to switch.

-So you are unable to login after the power fluctuations ?

-Could you please help us with the switch model number so that i will help you to access the switch .

Regards ,

Deepu Sekar

rahulmandava

I haven't tried to login in the recent past. But when I tried to once I got this issue, I am unable to either login via UI interface/Unleash app or connect via putty using IP address.

Switch model number is : ICX 7150-C12P

rahulmandava

I was able to login into switch now via IP Address login from browser. I don't see anything called firmware, but I do see this image version : (SW: Version 08.0.90dT213). Let me know if that is not the right one and / or if you need any information to further look into the issue ?

I do see few command options as well when I logged in, is there anything that I can run and see if the issue gets resolved ?

Deepu

Hi Rahulmandava

It looks like your Switch (ICX7150 Switch) may be booting from the secondary partition ( Note: Secondary partition contains the routing code) which is causing the bad connectivity issues. This could happen after multiple power outages, please follow up the next guide.

How to Fix Routing code issues on Lennar Home users via Web GUI.

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issues-on-Lennar-Home-users-via-Web-GUI/td-p/47959

How to Fix Routing code issues on Lennar Home users via CLI

Guide#1 for CLI:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issues-on-Lennar-Home-users/td-p/47305

Guide#2 for CLI:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-code-issue-in-your-ICX7150-Switch/td-p/47335

Note: if you have access to the Unleashed Dashboard and the Switch can be seen from there, it may look like the following image, ICX7150-C12-Router instead of ICX7150-C12-Switch, now before starting the steps of the guide, I will advise you to cable the computer directly to the Switch, since you will have a better connectivity than if you connect via wireless.

After fixing the issue of the Switch booting from the wrong partition, please perform an upgrade to the code 08095g UFI and upgrade both partitions primary and secondary with the switching code file named SPS08095gufi.bin, take into consideration that is the Switch is running a code lower than 08080 you need to upgrade twice, from the code you are to 08080f and then the recommended code 08095g UFI.

How to Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-using-a-USB-flash-drive/td-p/46781

How to upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-via-TFTP/td-p/47187

Upgrade a switch via Web GUI (ICX7150 Switch)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-via-Web-GUI-ICX7150-Switch/td-p/48200

Please try the most common username and passwords ( This is key sensitive so please include capital letters )

Username:admin password: Ruckus!

Username:admin password: Ruckus1

Username:admin password: Lennar

Username:super password: sp-admin

Admin usernames and passwords for the Ruckus Wi-Fi Access Points/Switch for Lennar home users

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Admin-usernames-and-passwords-for-the-Ruckus-Wi-Fi-Access-Points/td-p/46740

Regards,

Deepu Sekar

rahulmandava

Hi Deepu, none of the links you shared are working. I get a page not found error.

Deepu

Hi Rahulmandava

Could you please check the above links now , I have verified it which is working fine now .

Regards ,

Deepu Sekar

rahulmandava

I have tried again and it is the same. I am getting below page for all the urls. Maybe your hyperlink is not having complete url ?

The page you are trying to access was not found. Please check your URL for typos and try again.

Deepu

Hi Rahulmandava

I have verified the links which is working fine , could you please clear the browser cache and history and try to access the link .

Regards ,

Deepu Sekar

rahulmandava

I tried the web GUI options shared above, but still the issue is not resolved. Could you please suggest what else I can try?

rahulmandava

Hi Deepu,

I tried the web GUI option shared above, but issue still persists. Could you please help me the next steps?

rahulmandava

Hi Deepu, I have tried the option via Web GUI. Still it didn't resolve the issue. Could you please help me with the next steps?

rahulmandava

Can someone help me here ? I am not getting any response from last few weeks. I have setup temporary wifi bypassing ruckus, this is so annoying that it is not working in the first place and not getting support in the forum and no way to contact support directly.

rahulmandava

Can someone help me here ? I am not getting any response from last few weeks. I have setup temporary WIFI bypassing ruckus, this is so annoying that it is not working in the first place and not getting support in the forum and no way to contact support directly.

imran.sanadi@commscope.com

admin test

imran.sanadi@commscope.com

Hi @rahulmandava

Greetings!!!

Thank you for contacting Lennar Home Community.

Apologies for any inconvenience caused.

Hope you are doing well!!!

As per the case description, I could understand that your RUCKUS setup is not working after a power outage.

We will check some configurations on the Switch, please follow the below steps to check the same.

Please follow the below steps and help us with the queries,

1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Devices-IP-address-using-free-applications/td-p/47027

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-ICX-7150-12P-or-access-points-quot/td-p/47388

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command

enable

show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

rahulmandava

Hi Imran, not sure what is your reply pertaining to. But the problem is I am still having the issue, as I mentioned in one of my replies earlier, I tried the web GUI option that one of your colleague suggested. Still ruckus is not working as expected or before. Please let me know what else I can try? If we can schedule a call that will be great as I have been facing the issue since more than a month and still no resolution.