nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

Upgrade Firmware

dtsteinb

I want to upgrade the firmware but I was doing it via SSH via putty. I have nothing but issues doing it this way. I know there is a program now that can do it. I have lta-windows-386-0.0.45 but when I enter the IP/username/password it looks like it is trying to connect. After it gets to 5% it just closes. Is there a newer program or am I doing something wrong?

Find more posts tagged with

Accepted answers

All comments

pinky_ruckus

Hello @dtsteinb ,

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the information you shared.

As per the case description, I understand that you are looking to Upgrade the Switch using the upgrade tool.

To proceed further, we would need to check few configurations of the switch.

To check this, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find the IP Address of the RUCKUS Devices (Switch and APs) using IP Scanner free applications:

/kb/articles/10-how-to-find-the-ip-address-of-the-ruckus-devices-switch-and-aps-using-ip-scanner-free-applications

Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

/kb/articles/8-how-to-access-the-command-line-interface-cli-of-the-ruckus-icx-7150-c12p-switch

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Once you login to CLI, please enter the below commands and share the output.

Note: Hit Enter to accept each command

enable

show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

pinky_ruckus

Hello @dtsteinb ,

Greetings!

This is a follow-up in reference to the case you have opened in the Ruckus Lennar Support Community.

I would like to know if you require further assistance since our last correspondence. Should you have any questions or if the status of your case has changed, please let me know by responding to this post.

Please feel free to contact if you have any further concerns regarding the same.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

dtsteinb

Thank you for the response. Here is the information you requested.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2025.07.31 11:22:26 =~=~=~=~=~=~=~=~=~=~=~=
telnet@ICX7150-C12-Switch>en
No password has been assigned yet...
telnet@ICX7150-C12-Switch#sh version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Apr 6 2020 at 22:29:25 labeled as SPS08080f
(25976488 bytes) from Primary SPS08080f.bin
SW: Version 08.0.80fT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.24T225 (mnz10124)
Compiled on Thu Apr 21 06:08:52 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3845P2YG
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
--More--, next page: Space, next line: Return key, quit: Control-c                                                                  STACKID 1 system uptime is 32 day(s) 21 hour(s) 32 minute(s) 24 second(s)
The system started at 00:17:41 GMT+00 Sat Jan 01 2000

The system : started=cold start

==========================================================================
========== WARNING: Boot-monitor version mismatch!!! ==========
========== Please use "show boot-monitor" command for details ==========
==========================================================================
telnet@ICX7150-C12-Switch#sh flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25976488, Version:08.0.80fT211 (SPS08080f.bin)
Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPS08080f.bin)
Compressed Boot-Monitor Image size = 786944, Version:10.1.24T225
Code Flash Free Space = 1319395328
telnet@ICX7150-C12-Switch#exit
telnet@ICX7150-C12-Switch>quit
Invalid input -> quit
Type ? for a list
telnet@ICX7150-C12-Switch>
enable Enter Privileged mode
exit Exit from EXEC mode
nslookup Nslookup Utility
ping Ping IP node
show Display system information
stop-traceroute Stop current TraceRoute
sz On Premise SZ User Mode
traceroute TraceRoute to IP Node
telnet@ICX7150-C12-Switch>exit

pinky_ruckus

Hello @dtsteinb ,

Thank you for the response.

From the response you shared, I understand that the Switch is on the version 08.0.80f.

As the Switch is on the version 08.0.80f, you can use the upgrade tool to upgrade the Switch to the recommended version 08.0.95g.

Utilizing this tool is straightforward: users simply need to input the IP Address, Username, and password associated with the Switch into the software interface.

For your convenience, please find the necessary resources below:

1. Download the Upgrade software for Mac: https://support.ruckuswireless.com/software/3836-lennar-upgrade-tool-mvp-mac

2. Download the Upgrade software for Windows: Link: Upgrade Software for Windows

Access the Upgrade Software User Manual: Link: Upgrade Tool User Guide for Lennar SmartHome users

Please confirm if you were using the same link to use the upgrade tool.

Also, please share any screenshots if you are getting stuck at any point.

Thank you for your patience and understanding.

Regards,

Pinky Rajendran

RUCKUS Lennar Home Community

dtsteinb

This is the same software version I have now. When I putty in I see

telnet@ICX7150-C12-Switch>enable
No password has been assigned yet...
telnet@ICX7150-C12-Switch#

When I enter that IP via web browser it asks for username/password. How do I set that up?

I have 3 IP's for Ruckus

I am assuming I need to do this via the 10.0.0.246 IP.

dtsteinb

I will probably do it in the next couple of days. Do you know why when I do a speed test and I am connect via the Ruckus I cant break 90mb/s download (I have 200mb/s line) When I change and go through the Xfinity router I get the 200 mb/s. I was getting that speed before and now it seems crippled again.

dtsteinb

Do you know why all of a sudden I am not getting the speeds I was getting before? On a speed test connected using the Ruckus my download speed can now barley break 90 mb/s when it should be close to 200mb/s. If I use my Xfinity router I get very close to the 200 mb/s down. Do you cripped older versions of firmware? I would really like to upgrade but my last experiences have been horrible and there is NO phone number to contact anyone so if the switch doesnt come back I am in trouble as I work from home and need this.

imran.sanadi@commscope.com

Hi @dtsteinb
Greetings!

Thank you for contacting the RUCKUS Community forums.

As this case is now closed, please create a new post with the above description on the RUCKUS Lennar Support page.

Thank you for your understanding.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support