nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

ICX8200 configuration

stobbertt

Hi,

I am having some problems configuring an icx8200 switch. I am following the Ruckus Fastiron Web Manamgement Interface UserGuid 10.0.10. The management port is assigned with an IP address, users are created and authentication is set up.
According to the show web command, the HTTP and HTTPS servers are enabled. However, no IP is displayed under Web Session Management.
The laptop is connected directly to the management port via LAN cable. I can ping the ip, but cannot reach it via the browser

Thanks for help

Patrick

Find more posts tagged with

Accepted answers

Mayank

Hi stobbertt,

I would recommend you upgrade this switch to 10010c_cd2 and then test it.

Thanks

stobbertt

Hi,

i found a solution, i use the cli command "for the facory reset

All comments

BenBeck

Hey @stobbertt

Can you ping the switch? Could you give the output of "show run | inc web"?

Thanks in advance.

stobbertt

Hey Ben,

thanks for your answer. Yes i can ping the switch over the ip address from the management port.

when i use the command show run, witch details do you need?

thanks

stobbertt

sorry my mistake....

aaa authentication web-server default local

web-management http

web-management session-time 300

web-management tcp-port 80

management-access mac XX:XX:XX:XX deny web

"mac address has been made unrecognizable"

BenBeck

Are you trying to block a mac with 'management-access mac XX:XX:XX:XX deny web'? If not, try removing that command. The rest looks okay to me and you should have access on port 80.

Mayank

Hey Stobbertt,

Thank you for reaching us.

I have a question for you here :

What is the firmware version you are on ?

If you are using 10.0 flat I recommend you upgrade this switch to 10010c_cd2 and then test.

Moving Forward If this issue is not resolved , Please log a ticket with the below link so that we will help you further.

https://support.ruckuswireless.com/contact-us

I hope this information helps you

Please feel free to leave us a message if any concerns

Note: Please feel free to mark the post as ACCEPTED SOLUTIONS if its addressed your query.

Thanks

stobbertt

How can i remove the MAC Address? I don´t find the command

stobbertt

Hi,

i use the Firmware RDR10010b / Version 10.0.10bT253

Mayank

Hi stobbertt,

I would recommend you upgrade this switch to 10010c_cd2 and then test it.

Thanks

stobbertt

Hi, the WebUserInterface is running now. Thanks for Help.

But how can i configure the Switch to a Layer 2 Switch, i don´t need the L3 Function.

Thanks a lot

Mayank

Hi Stobbertt,

Glad to know that the Web user interface is running.

In 8200, The Switching image was deprecated with 10.0 and each platform will only use one image starting with 10.0.

ALL the L3 image support L2 features starting with 10.0, Only routing image are available for all supported models.
Switching features are still available in the routing image.

>The 8200 by design doesn't support l2 image so there is no ip default-gateway command.

>Instead we need to specify the route to forward the traffic to an external subnet. We can either use static routes, default routes or a routing protocol.

>If you want to use the ICX8200 switch as a L2 device follow the below steps:

You just need to add a default route to the device, And then add the VLANs you want. The ICX8200 model can only run L3 firmware images. That's why we need to add a default route for it to start behaving as an L2 switch, where it is only passing VLAN traffic in and out. We also need to identify the VLAN where this default route communication goes through. And then create a virtual interface and assign the IP that will be used for management and for communication with the default gateway.

Example:

-Create the virtual interface and assign the IP form MGMT and default route:

ICX8200-switch#conf t
ICX8200-switch(config)#vlan 10
ICX8200-switch(config-vlan10)#interface ve 10
ICX8200-switch(config-if-ve10)#ip address 10.10.10.2/24

Here's the command for the default route:

ICX8200-switch#conf t
ICX8200-switch(config)#ip route 0.0.0.0/0 10.10.10.1 (IP address of your ICX7850 router, which is the default gateway for the management vlan)

ICX8200 with the code 10.00, this code only came in routing, so you can configure the IP address under a VE, loopback or port.

Beginning with the 09.0.00 release, when a VLAN is configured, a virtual routing interface is statically mapped to the VLAN ID. However,
only when you issue the interface ve-num command does the virtual interface get created.

Please refer the below link for your reference :

https://community.ruckuswireless.com/t5/RUCKUS-Self-Help/IP-Address-Assignment-in-8200-Devices/td-p/77961

I hope this information helps you

Please feel free to leave us a message if any concerns

Note: Please feel free to mark the post as ACCEPTED SOLUTIONS if its addressed your query.

Thanks

stobbertt

hi,
thanks again for your active support. Now I have the following problem, I would like to make the switch actively accessible in the network. As I have only made the IP of the management port accessible with the instructions, how can I make the web interface actively accessible in the network?
Thanks in advance