Info: Device Key or Cert file is not available

Question

My ICX7150-C12P has been working flawlessly, and powering my CCTV around my premises. However, today, my cameras went offline as well as my APs, and my serial connected to the switch populates with Info: Device Key or Cert file is not available over and over, every 2 seconds. I tried reloading and using the webportal, to no avail. Please advise! Thank you

imcobra · Answer

Here is the info from the commands you requested:

UNIT 1: compiled on Apr 11 2023 at 00:06:30 labeled as SPS08095j

(31457280 bytes) from Primary SPS08095j.bin (UFI)

SW: Version 08.0.95jT211

Compressed Primary Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

Compiled on Tue Nov 29 12:43:26 2022

HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X10GR POE 12-port Management Module

Serial  #:#########

Software Package: BASE_SOFT_PACKAGE

Current License: 2X10GR

P-ASIC  0: type B160, rev 11  Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8 MB boot flash memory

2 GB code flash memory

1 GB DRAM

STACKID 1  system uptime is 10 hour(s) 8 minute(s) 5 second(s)

The system started at 00:06:39 GMT+00 Tue Apr 11 2023

The system : started=cold start

Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)

Compressed Sec Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)

Compressed Pri Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

Compressed Sec Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

Code Flash Free Space = 1069690880

a

Commencing sanity check for device certs ...

Verifying TPM files ...

Failed: Check TCSD_PS Files

The switch was from my former Lennar home. How do I proceed with replacement? Thank you

imcobra · Answer

Here is the info from the commands you requested:

Info: Device Key or Cert file is not available

UNIT 1: compiled on Apr 11 2023 at 00:06:30 labeled as SPS08095j

(31457280 bytes) from Primary SPS08095j.bin (UFI)

SW: Version 08.0.95jT211

Compressed Primary Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

Compiled on Tue Nov 29 12:43:26 2022

HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X10GR POE 12-port Management Module

Serial  #:#########

Software Package: BASE_SOFT_PACKAGE

Current License: 2X10GR

P-ASIC  0: type B160, rev 11  Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8 MB boot flash memory

2 GB code flash memory

1 GB DRAM

STACKID 1  system uptime is 10 hour(s) 8 minute(s) 5 second(s)

The system started at 00:06:39 GMT+00 Tue Apr 11 2023

The system : started=cold start

Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)

Compressed Sec Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)

Compressed Pri Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

Compressed Sec Boot Code size = 786944, Version:10.1.26T225 (mnz10126)

Code Flash Free Space = 1069690880

a

Commencing sanity check for device certs ...

Verifying TPM files ...

Failed: Check TCSD_PS Files

The switch was from my former Lennar home. How do I proceed with replacement? Thank you

Mayank · Answer

Hi imcobra,

Thank you for the update.

It looks like we need to replace the Switch.

Please log a ticket with the below link so that we will help you to process RMA

https://support.ruckuswireless.com/contact-us

Note: Please confirm us if you are from Lennar homes

I hope this information helps you

Please feel free to leave us a message if any concerns

Thanks