nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

ICX 7150-C12P & R510 AP

imcobra

I have an ICX 7150-C12P and two R510 APs. I recently updated to 08.0.95jT211, and as of today, only one of my two R510 AP broadcasts my customized networks; however, one of my R510 has started only to broadcast ISLAND-XXXXXX, and when I hold the factory reset button, my AP reboots, and broadcasts ISLAND-XXXXXX shortly after. Please advise on the best action to get both APs back up and running. Regards!

Find more posts tagged with

Accepted answers

Orlando_Elias

Hello, the AP in port 1/1/3 has the version 104.0.0.0.1347 This version is not compatible with Unleashed. Please use the IP address of the AP (+ Management address (IPv4): XXXXXX) in your web browser and change the firmware to Unleased firmware 200.14.6.1.203
This can be done at Management>Upgrade

All comments

Orlando_Elias

hello @imcobra

Would you be able to copy-paste the output of the below commands?
show run vlan, show lldp neig det

imcobra

#show run vlan

vlan 1 name DEFAULT-VLAN by port
!
!

#show lldp neig det

LLDP is not running

Orlando_Elias

Please enable lldp with the commands:
config terminal, lldp run

give some minutes and run the command 'show lldp nei det' one more time.

Thanks so much.

imcobra

Hi there,

I did 'lldp run,' and assuming you're looking for my two APs, I included those in the following text with some info redacted, for this is a public forum.
Did you also need my other ports and their information, or just for the APs? Regards!

Local port: 1/1/2
Neighbor: XXXXXX, TTL 100 seconds
+ Chassis ID (MAC address): XXXXXX
+ Port ID (MAC address): XXXXXX
+ Time to live: 120 seconds
+ System name: RuckusAP
+ System description : "Ruckus R510 Multimedia Hotzone Wireless AP/SW Ver\
sion: 200.14.6.1.203"
+ System capabilities : bridge, WLAN access point, router
Enabled capabilities: bridge, WLAN access point
+ Management address (IPv4): XXXXXX
+ Port description : "eth0"
+ Link aggregation: capable, but not aggregated
+ 802.3 MAC/PHY : auto-negotiation enabled
Advertised capabilities: 10BaseT-HD, 10BaseT-FD, 100BaseTX-HD,
100BaseTX-FD, fdxPause, fdxAPause, 1000BaseT-FD
Operational MAU type : 1000BaseT-FD

Local port: 1/1/3
Neighbor: XXXXXX, TTL 95 seconds
+ Chassis ID (MAC address): XXXXXX
+ Port ID (MAC address): XXXXXX
+ Time to live: 120 seconds
+ System name: RuckusAP
+ System description : "Ruckus R510 Multimedia Hotzone Wireless AP/SW Ver\
sion: 104.0.0.0.1347"
+ System capabilities : bridge, WLAN access point, router
Enabled capabilities: bridge, WLAN access point
+ Management address (IPv4): XXXXXX
+ Port description : "eth0"
+ Link aggregation: capable, but not aggregated
+ 802.3 MAC/PHY : auto-negotiation enabled
Advertised capabilities: 10BaseT-HD, 10BaseT-FD, 100BaseTX-HD,
100BaseTX-FD, fdxPause, fdxAPause, 1000BaseT-FD
Operational MAU type : 1000BaseT-FD

Orlando_Elias

imcobra

Hi there,

In the Management for the AP with the incompatible version, I tried using the Upgrade with FTP to fwupdate1.ruckuswireless.com, but it failed to download. Is there directions for using the management portion of the AP? I am only familiar with Ruckus Switches. Thank you!

imcobra

Nevermind! Found the firmware file, and downloaded to the AP locally! Now the management page has been updated to the Unleashed Portal. It shows my two APs now! Thank you for the help!

Orlando_Elias

I'm very happy to know my knowledge has been useful in making your day better! Happy internet browsing!