My both APs stopped working, it seems like switch has some problem. How can I replace it?
Hi @Mohitgahlot14
Greetings of the day!!!
Thank you for the response and the update.
This issue may happen when the Switch runs on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. If the Switch boots up on the other partition (Due to a power outage/power spike may be) which may be running on a ‘Routing Code’ results in causing this issue. To check the same please follow the below process.
Please follow the below steps and help us with the queries,
1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P
I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.
How to find my Ruckus “Devices IP address” using free applications:
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Devices-IP-address-using-free-applications/td-p/47027
2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”
How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-ICX-7150-12P-or-access-points-quot/td-p/47388
If you can access the Command line should look like this:
ICX7150-C12 Router> OR
ICX7150-C12 Switch>
Please enter the below commands once you log in to CLI and share the output.
Note: Hit Enter to accept each command
enable
show version
show flash
Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.
Thank you again for your patience.
Best regards,
Imran Sanadi
Lennar Home Community.
Thank you for contacting Lennar Home Community.
Hope you are doing well!!!
From the case description, I could understand that your RUCKUS Access Points are not working.
Could you please let us know?
1. Was this working before or is it a new installation? If it worked before, was there any power outage before you started facing this issue?
2. On your switch while it's plugged into the outlet, do you see any lights on? (Amber or green) Please let us know which lights are on. (Please refer to the below picture and share a picture of the same)
3. Is your Internet Connection from the Internet Service Provider (ISP) stable and working? (You could check this by connecting to your local router Wi-Fi or from an ethernet cable from Router to a laptop/PC)
4. May I know how many Access Points are connected to the Switch? Could you please let me know the light status on the Access Points? Any of these lights are on (Please refer to the below picture and share a picture of the same)
Please help us with pictures of your ICX-7150-C12P Switch showing the status of the lights. Also, light the status of Access Points.
Before uploading the photos please log in to the RUCKUS account and you can upload the image.
Please let us know the answers to the above queries or if you have any queries in this regard.
It was working for 2 year, no power outage.
Yes, see attached pictures
Yes, it’s is stable and working.
2, see attached pictures
Thank you for the response and the information you shared.
May I know from where the yellow ethernet cable is coming? (Please refer to the below screenshot)
Please let me know if you have any queries in this regard.
Thank you again.
Modem
Thank you for the response and confirmation.
As the ethernet cable which is coming from the Router/Modem-Router Combo device is plugged into the wrong port on the Switch panel. It must be plugged into any 1 in-12 ports as shown in the below screenshot. Please unplug the yellow ethernet cable and plug it into the correct port.
Please refer to the short guide link below about how to connect the devices as reference:
Most common Setups for Lennar homes users:
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Most-common-Setups-for-Lennar-homes-users/td-p/47106
I followed above steps and it’s working again, thanks
Greetings!!!
Great!!! Good to know that it’s working again.
Could you please let me know if you were able to get the CLI access and performed the steps as suggested in previous posts? Please confirm.
