I'm trying to update an ICX7150-C12 with a newer firmware. It's currently running 8.0.61a, and I am aware upgrading past this requires that you load both the firmware & the eUFI image, which I have done. I can get the switch to update (on the Secondary Flash) and it seems to take the install as well as the reimage, but when you try to boot to secondary, it gives me a notice that it's "Skipping Bad Block", as seen below. I've included my whole boot sequence here, as there's likely information in here about where my problem is occurring. I'm upgrading via TFTP, and I have tried multiple different versions of firmware, with identical results. I've also tried copying the primary flash back over to the secondary and starting from scratch to no avail. Can anyone shed some light on this?
Booting image from
Secondary
NAND read: device 0
offset 0x4000000, size 0x2000000
Skipping bad block
0x05a00000
Skipping bad block
0x05b00000
33554432 bytes read: OK
## Loading kernel
from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90e
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fa00
Data Size: 2401142 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: 8399a11a
## Loading kernel
from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90e
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fa00
Data Size: 2401142 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: 8399a11a
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk
from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a072c
Data Size: 23816895 Bytes = 22.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: e786d75c
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from
FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e4d4
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e4d4 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end
6500d19e
Starting kernel ...
Mounting file
system...
booting with 4.4
kernel
NAND Type: Micron
NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition
mounted
Resource partition
is mounted!!
Please download UFI
image to install packages
/etc/process_packages.sh:
line 148: can't create /.pkg/error.log: nonexistent directory
Package installation
is incomplete, related functionalities may not be available
dhcpd executable
file is not present.
Starting up system
statistics daemon...
Starting systatsd
done
Starting up health
monitor daemon...
Log Level 7:
Daemonized systatsd
Systatsd Logging Env
is not set, initializing loglevel to: 7
Setting connection
to systemlogger
Starting hmond done
Hmond Logging Env is
not set, initializing loglelvel to: I
Setting connection
to systemlogger
Backup is fine
Kernel crashdump is
disabled.
dma_mem_base:
0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len:
0xb00000
Creating TUN device
Starting TPM Infra
Group tss and User
tss created
kernel.hostname =
localhost
hostname set to
localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the
FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=60:9c:9f:e6:2d:f9?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=172.21.28.103:172.21.7.249::255.255.0.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT
NOT DISABLED
platform type 90
OS>
Loaded Image
SPS08090e from Sec Built on (UTC): Tue Nov 19 12:27:26 2019
Enabling Console
Logging
Installed CPLD Version
0x4:0x7
Recommended CPLD
Version 0x4:0xa
Upgrading CPLD to
0x4:0xa
CPLD is upgraded
Successfully !!!
!!WARNING: System is
going to Power Cycle to load new CPLD !!
CPLD is upgraded Successfully
!!!sil_ramfs_creat: Failed to create file /var/log/pdc/pdc_errorlog.txt
Could not create
ramfs file!
pdc_errorlog
Could not open ramfs
file!
fitrace_tmp.errorlogUpgrade
from pre 8.0.80 image. Dual mode to VLAN config upgrade needed
Hotplugger Daemon
Initialized ..
External USB disk is
not mounted or plugged in.
Stopping health
monitor daemon...
Stopped health
monitor daemon
Sent SIGTERM to all
processese = 116Stopping system statist
Sent SIGKILL to all
processes
Requesting system
reboot
[ 73.820342] reboot: Restarting system
[ 73.864242] Asserting GHPIO[7] reset sequence
from Kernel ...
