Any specific commands to switch to switch code from router code on 8070d?

Question

Any specific commands to switch to switch code from router code on 8070d? I somehow ended up with SPR code on primary and secondary

Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 29451996, Version:08.0.70dT213 (SPR08070d.bin)

Compressed Sec Code size = 29451996, Version:08.0.70dT213 (SPR08070d.bin)

Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225

Code Flash Free Space = 1319104512

unknown · Answer

Good Day:Your command on that platform is:copy tftp system-manifest 10.1.2.3 FI08080e_Manifest.txt primary switch-image

Download and extract 08080e, but do not worry about all the different platforms it supports... You want all 664 MB of it in a folder.  In my case it is c:\TFTP-Root\08080eUnder there are folders like c:\TFTP-Root\08080e\ICX7150, ICX7250, ICX7450, etc.I personally use Tftpd64 by Ph. Jounin, but there are many great TFTP programs available such as the one from Solar Winds.  In my case, I point the "Current Directory" to c:\TFTP-Root\08080e\ in my TFTP program.On the switch, set an IP on an interface or VE on the same subnet you are on.  If you do it correctly, you should be able to ping your computer "ping 10.1.2.3" for example.This command below assumes your computer is 10.1.2.3Send the Switching "SPS" Firmware:copy tftp system-manifest 10.1.2.3 FI08080e_Manifest.txt primary switch-imageBy historical convention, we send the switching firmware to the primary and routing firmware to the secondary on all Fast-Iron type devices.  Before upgrading one switching firmware version to another, I would backup "copy" the primary => secondary.Likewise, if I were running routing firmware, I would boot the secondary.  If I were going to upgrade, I would backup secondary => primaryHere is the command to upgrade the Routing firmware (for reference):copy tftp system-manifest 10.1.2.3 FI08080e_Manifest.txt secondary router-image***When done the "show flash" will show:Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 25973456, Version:08.0.80eT211 (SPS08080e.bin)

Compressed Sec Code size = 29451996, Version:08.0.70dT213 (SPR08070d.bin)

Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225

Code Flash Free Space = 1319104512You probably want to verify the checksum:Switch#verif md5 pri.......................................................DoneSize = 25973456, MD5 03420970e5d4bb0cd48f5bc6485541a8Also the boot preference:Switch#sh boot-prBoot system preference(Configured):        Use DefaultBoot system preference(Default):        Boot system flash primary        Boot system flash secondary

jijo_panangat · Answer

Hey Sal,There is no cmd to change to switching code when your primary and secondary flash runs routing code.Compressed Pri Code size = 29451996, Version:08.0.70dT213 (SPR08070d.bin) >> Routing

Compressed Sec Code size = 29451996, Version:08.0.70dT213 (SPR08070d.bin) >> RoutingIf one of it had a switching code, you can do a 'boot system  flash primary/secondary' to load the image. In this case, you need to load the switching code first and use the above to boot from the partition.ThanksJijo

hashim_bharooc1 · Answer

Hi Sal,Here is the link to both the codes you need a credential to access it:https://support.ruckuswireless.com/software/1913-ruckus-icx-fastiron-08-0-70d-software-release-zipUnzip them with directory structure use tftp server make sure you have connectivity and  run Commands:copy tftp flash 10.176.4.25 /pub/sre/Released/ironware/FastIron/08070/08070a/ICX7150/Images/SPS08070a.bin priwrite memreload.10.176.4.25  is example use your own IP address.
When you go to Switched code all your Routing Interfaces will be gone so please be aware and your Management VLAN will have to be configured with an IP address for connectivity.

Hope this helps.
ThanksHashim