nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

ICX 7150: Not letting me create a Router-Interface

unknown

HELP!!!

I've been trying to create a vlan with its own dhcp server, however for some reason my switch is not letting me create a router-interface. I do have the dhcp pool ready for it, though.

below is code:
ICX7150-C12 Switch(config)#vlan 30

ICX7150-C12 Switch(config-vlan-30)#tagged e 1/1/3
Added tagged port(s) ethe 1/1/3 to port-vlan 30.

ICX7150-C12 Switch(config-vlan-30)#tagged e 1/1/4
Added tagged port(s) ethe 1/1/4 to port-vlan 30.

ICX7150-C12 Switch(config-vlan-30)#untagged e 1/1/5
Added untagged port(s) ethe 1/1/5 to port-vlan 30.

ICX7150-C12 Switch(config-vlan-30)#router-interface ve 30
Invalid input -> router-interface ve 30
Type ? for a list

ICX7150-C12 Switch(config-vlan-30)#exit

ICX7150-C12 Switch(config)#show run
Current configuration:
!
ver 08.0.70cT211
!
stack unit 1
module 1 icx7150-c12-poe-port-management-module
module 2 icx7150-2-copper-port-2g-module
module 3 icx7150-2-sfp-plus-port-20g-module
!
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 30 by port
tagged ethe 1/1/3 to 1/1/4
untagged ethe 1/1/5
!
!
!
!
!
!
!
!
!
!
!
!
!
aaa authentication web-server default local
aaa authentication login default local
dhcp-gateway-list 10 192.168.30.1
ip address 192.168.1.90 255.255.255.0
no ip dhcp-client enable
ip dhcp-server enable
!
ip dhcp-server pool testvlan30
excluded-address 192.168.30.1
lease 1 0 0
network 192.168.30.0 255.255.255.0
option 3 ip 192.168.30.1
deploy
!
!
username telepro password .....
username user password .....
username ruckus password .....
username admin password .....
!
!
interface ethernet 1/3/1
speed-duplex 1000-full
!
interface ethernet 1/3/2
speed-duplex 1000-full
!
!
!
!
!
!
!
!
!
end

Find more posts tagged with

Accepted answers

All comments

josue_jimenez_c

Hi, you may be probably running switching code, you need to run routing code, the routing code may look like this: SPR08061c, "R" for routing.

unknown

Hi Jose,

1. Is your switch in Layer 3 mode? (using router image, instead of switch)

Do this:

show flash
show boot

Make sure that the image it is booting to has a letter R in it.

2. If not, do the below:

Usually, the secondary image on switches is the Router image. To make it boot to secondary permanently do this:

conf t
boot system flash secondary
write memory
reload
y

Happy routing 🙂

Cheers,
Alex

unknown

IT WORKED! Thank you!!!

unknown

It worked but now i dont have any internet in that vlan 😕
I set vlan 30 with ports 6-12.
but i have my internet connected to port 1, the default vlan.

how can i send internet to vlan 30 while still handing out IP's in the 30 subnet?

josue_jimenez_c

I would try a ip route to the default gateway,
device(config)# ip route 0.0.0.0/0 x.x.x.x

This link can help you out: http://docs.ruckuswireless.com/fastiron/08.0.70/fastiron-08070-commandref/GUID-2E5545F8-42DD-476B-A0...

jon_maiman_iyni

Please capture the output from the following commands and post it to the thread:

Skip
Show run
Show Version
Show Ip Int
Show Ip Route
page

Best guess without more information is you don't have a "WAN" IP address for the port connected to the Internet. Since the ICX7150 is running router code, you need to be able to route up to the Internet. Second guess is your Upstream Internet Router doesn't have routes back to your ICX7150 for the locally hosted subnets you created. The output from the above commands should help isolate the problem.

--Jon

unknown

please see below:

ICX7150-C12 Router(config)#skip
Invalid input -> skip
Type ? for a list

ICX7150-C12 Router(config)#show run
Current configuration:
!
ver 08.0.70cT213
!
stack unit 1
module 1 icx7150-c12-poe-port-management-module
module 2 icx7150-2-copper-port-2g-module
module 3 icx7150-2-sfp-plus-port-20g-module
!
!
global-stp
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 2 name IP-Subnet_10.1.2.0/24 by port
!
vlan 30 by port
untagged ethe 1/1/6 to 1/1/12
router-interface ve 30
!
!
!
!
!
!
!
!
!
!
!
!
!
aaa authentication web-server default local
aaa authentication login default local
boot sys fl sec
ip dhcp-server enable
!
ip dhcp-server pool testvlan30
excluded-address 192.168.30.1
lease 1 0 0
network 192.168.30.0 255.255.255.0
option 3 ip 192.168.30.1
deploy
!
ip route 192.168.30.0/24 192.168.1.254
!
username telepro password .....
username user password .....
username ruckus password .....
username admin password .....
!
!
!
!
!
!
!
!
!
interface ethernet 1/3/1
speed-duplex 1000-full
!
interface ethernet 1/3/2
speed-duplex 1000-full
!
interface ve 30
ip address 192.168.30.1 255.255.255.0
!
!
!
!
!
!
!
!
!
!
end

ICX7150-C12 Router(config)#Show Version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Aug 30 2018 at 04:48:29 labeled as SPR08070c
(29437672 bytes) from Secondary SPR08070c.bin
SW: Version 08.0.70cT213
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
Compiled on Tue Jul 24 10:23:08 2018

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3811Q1WN
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 38 minute(s) 25 second(s)
The system started at 00:01:54 GMT+00 Sat Jan 01 2000

The system : started=cold start

ICX7150-C12 Router(config)#Show Ip Int
Interface IP-Address OK? Method Status Protocol VRF
Ve 30 192.168.30.1 YES NVRAM up up default-vrf

ICX7150-C12 Router(config)#Show Ip Route
Total number of IP routes: 1
Type Codes - B:BGP D:Connected O:OSPF R:RIP S:Static; Cost - Dist/Metric
BGP Codes - i:iBGP e:eBGP
OSPF Codes - i:Inter Area 1:External Type 1 2:External Type 2
Destination Gateway Port Cost Type Uptime
1 192.168.30.0/24 DIRECT ve 30 0/0 D 39m7s

ICX7150-C12 Router(config)#page
Invalid input -> page
Type ? for a list

unknown

jon_maiman_iyni

As I suspected, you don't have a "WAN" IP Address to your upstream Internet Router. From when you connected your laptop to the Internet directly, your IP Subnet for the Internet is 192.168.1.0/24 and your gateway (next hop) is 192.168.1.254. You can create a VE in VLAN 1 (the default VLAN) and have it get an address via DHCP. The config. would be approx.:

vlan 1
router-interface ve 1

interface ve 1
ip dhcp-client

You will still need the default route to the internet:

ip route 0.0.0.0/0 192.168.1.254

However, this only fixes the problem in one direction (sending traffic upstream to the Internet). You will need a route on your Internet Gateway pointing to your ICX switch for the 192.168.30.0/24 network for downstream traffic.

This begs the question, if you only plan on having one IP Subnet 192.168.30.0 on your ICX Switch, why are you running router code? Wouldn't it be simpler to just use your switch as layer 2 only and configure your Internet Gateway to handout addresses in the 192.168.30.0 subnet for clients? Since the Internet Traffic will be NAT'ed anyway, you really could just leave the DHCP clients be assigned in the 192.168.1.0 subnet your Internet Gateway is already configured for.

--Jon

unknown

Need to get myself more familiar with these ICX products.

We will be installing a new ICX 48 port in an office that will require several vlans where only some are allowed internet access. And we wanted everything to be driven by the ICX switches.

Either case, I still haven't gotten vlan 30 to work correctly.

Does ruckus offer some sort of remote support or training?

jon_maiman_iyni

Jose,

Where are you located? Your best bet is probably to engage a Ruckus Channel Partner in your area for assistance (at least with your initial configuration and testing).

--Jon

unknown

We are located in South Texas.

chase_holland

Jose,

Where in South TX are you located? Want to see if we can have an SE give you a call and talk through your questions.

Thank you,

Chase

jijo_panangat

Hi Jose,

You can also open a TAC case with us for remote assistance, If you think that should solve the problem.

Thanks
Jijo

unknown

Mission, Texas. Sure! That would help a lot.