nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

ICX 7150 Firmware upgrade 08.0 to 10.0

Cibolo

Can my ICX 7150 grade from 08.0 to 10.0? Do I have to start at 08.1 to 08.2 etc or can I go straight from 08.0 to 10.0?

Thanks!

Find more posts tagged with

Accepted answers

BenBeck

Correct. It will change the image type from switching (later 2) to routing (layer 3). If you are not having any issues, I would advise leaving the code as is. If you are adamant about upgrading, I would advise 8095n and using the SPS08095nufi image so it is seamless.

All comments

BenBeck

You would have to go through 8080f. I would like to put a giant disclaimer out there for you. There are tons of CLI, syntax, etc. changes in 10.x. Also, only the router image exists in 10.x. I would only advise upgrading to 10.x if you are very comfortable with what you are doing and have physical access.

Cibolo

Ben,

I have upgraded to the following: show version (shown below):

What would be the next version that I will need to install?

Yes, I have physical touch to the switch.

Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on May 6 2022 at 23:24:50 labeled as SPS08095g
(31457280 bytes) from Primary SPS08095g.bin (UFI)
SW: Version 08.0.95gT211
Compressed Primary Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Compiled on Thu Apr 21 00:08:52 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3816Q1GY
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 1 day(s) 6 hour(s) 35 minute(s) 20 second(s)
The system started at 08:55:28 GMT-06 Sat Feb 08 2025

The system : started=warm start reloaded=by "reload"

BenBeck

Hey there. You can upgrade to 10.x from that patch, but please make note that you are running the switching image (SPS08095g). This means when you upgrade to 10.x (recommend 10.0.10f_cd1), you will be forced to the router (SPR) image. This will likely cause you to lose IP addressing and your gateway definition. You will need to define a VE and routes via console post-upgrade. There are also many syntax changes. Please ensure you review the respective upgrade guide should you decide to move to 10.x. 8095n is the current recommendation for ICX7150.

https://support.ruckuswireless.com/products/108-ruckus-icx-7150-campus-switches#sort=relevancy&f:@commonproducts=[ICX%207150]

Cibolo

The 10.x upgrade will change my switch into a router?

The IP addresses that I will need would be my ISP router and internal IP addresses?

Thank you for the quick responses.