nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

Lennar ICX box no longer turning on

hangity

Ruckus ICX 7150 no longer powering up. No lights at all on the switch. Tried multiple different outlets, power cords, etc. The access points in the ceiling are not powering on either. Not sure when it happened. I just noticed it when I realized the Kevo Plus that was attached to the ethernet was no longer working. I suspect just faulty equipment. Is there another solution for this problem here?

Find more posts tagged with

Accepted answers

All comments

imran.sanadi@commscope.com

Hello @hangity

Greetings!!!

Thank you for providing the information.

Based on the details you've shared, it appears that your RUCKUS ICX-7150-C12P Switch is not operational.

If that doesn't work even with a working power cord or other power outlets, I recommend again attempting a physical factory reset multiple times, as outlined in our RUCKUS Lennar Knowledge Base self-help article accessible through this link and VIDEO:

/kb/articles/11-process-for-performing-a-physical-factory-reset-hard-reset-on-the-ruckus-icx-7150-c12p-switch

Video link: https://www.youtube.com/watch?v=6jHMTdo_hK4

If the initial reset attempts do not resolve the issue, please try resetting your switch multiple times (approximately 10-15 times) using the method described in the article. In some cases, repeated attempts have successfully resolved similar issues. Upon successful reset, the SYST and PWR lights should turn GREEN.

Please proceed with these steps and let me know if the switch powers on successfully afterward.

Thank you for your patience and cooperation in this matter.

Best regards,

Imran Sanadi
RUCKUS Lennar Home Community

imran.sanadi@commscope.com

Hi @hangity

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

hangity

Hello, apologize for the delay. I’ve tried multiple times to reset the device according to the video and instructions, including with other outlets, but with no success.

hangity

To clarify: tried resetting it with the reset button and paper clip a few times as well and still no power or light indicating the device is working

imran.sanadi@commscope.com

Hi @Jxck

Greetings!!!

Thank you for the response and the update.

I hope this message finds you well.

To proceed, we kindly request that you follow the steps outlined below:

1. Take out your Switch from the cabin. Plug your ICX-7150-C12P Switch into a functioning power outlet.

2. Capture both pictures and a video of the switch, focusing on the following:

- The status of the lights on the switch.

- The cord connected to the switch.

- The switch plugged into a working power outlet.

We recommend referring to the example pictures provided below to ensure clarity in capturing the required details:

Please use the provided link to upload a video. We advise referencing the EXAMPLE VIDEO in the Google Drive link provided to ensure consistency in the recording:

Kindly shoot a video similar to the EXAMPLE Video provided in the link.

In the video, please ensure to capture the following:

1. Show the plug of the ICX-7150-C12P Switch being connected to a working outlet.

2. Simultaneously, display the light status on the switch.

https://drive.google.com/drive/folders/16lG-j0MSKzjqBJSY4rsgh4myUlseA9bz?usp=sharing

Should you have any queries or require further assistance, please do not hesitate to reach out. We are here to help.

Please Confirm once uploaded.

Thank you for your cooperation, patience, and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community