nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

ICX7150 switch boot mode

pankajkondekar

My icx7150 is stuck in boot mode, tried reset option but not working.

tried option 1-

After performing the factory reset using a paper clip 20-25 times, still see the Amber light on SYST

tried software recovery

getting error

Bad FIT kernel image format!
ERROR: can't get kernel image!

Find more posts tagged with

Accepted answers

imran.sanadi@commscope.com

Hi @pankajkondekar

Thank you for sharing the information.

Based on the troubleshooting done, you confirmed, and we saw that after the reset, booting up the Switch, and trying the software recovery process, the failure persists. This Switch unit Should be RMA (Return Merchandise Authorization) in simple words replacing it.

Feel free to contact us via chat, comment you already have a post, copy the link from the post (URL), and paste it into the chat to start the unit replacement.

Please follow the steps as shown in the below example:

As shown in the below picture, copy the link and share it via chat from the link provided:

The below link is to contact us by chat (only)

https://support.ruckuswireless.com/contact-us

Did I answer your queries? If yes, hit the Kudos buttons and also accept the answers as Accepted solutions.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

All comments

pankajkondekar

Tried steps from post

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-a-Software-recovery-on-an-ICX7150-switch/m-p/47483/thread-id/1816

getting error Retry count exceeded; starting again .......

is this still software issue or Hardware issue ?

icx7150 reboot mode 1.PNG icx7150 reboot mode 2.JPG

pankajkondekar

show_image

ICX7150-Boot>show_image
===========================
Primary :
NAND read: device 0 offset 0x0, size 0x200
512 bytes read: OK
SPS08090d(28660224)
Secondary:
NAND read: device 0 offset 0x4000000, size 0x200
512 bytes read: OK
SPS08090d(28660224)
===========================
ICX7150-Boot>

ICX7150-Boot>reset
resetting ...
device 0 offset 0x0, size 0xc0000
using GPIO[7] to reset

Ruckus Wireless Bootloader: 10.1.15T225 (Jan 30 2019 - 23:08:47 -0800)

Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK

ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0xa
Writing Shmoo values into flash .....

device 0 offset 0xbfe00, size 0x200
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Secondary

NAND read: device 0 offset 0x4000000, size 0x2000000
8 ecc_errors after reading 5b48000:5b49c00
iproc_nand_read_page returned 2
NAND read from offset 4000000 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from secondary, no valid image; trying to boot from primary
device 0 offset 0x0, size 0xc0000
BOOTING image from Primary

NAND read: device 0 offset 0x0, size 0x2000000
8 ecc_errors after reading 1b48000:1b49c00
iproc_nand_read_page returned 2
NAND read from offset 0 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!

pankajkondekar

@ Imran Sanadi-

can you please help ?

Mayank

Hi Pankajkondekar,

Thank you for posting your query !!!

I understand that ICX 7150 is stuck in boot mode and you already tried the reset option and software recovery but the issue remains the same.

I have a question for you here :

1> Did you try to boot the iCX 7150 from the primary and secondary image from the service os try to boot the primary or secondary partition like this: boot_primary or boot_secondary.