I have a ICX 7150 since 2020 and was never upgraded. I am at a lost as to how to locate the version and then what upgrade is necessary to use. Any help would be appreciated.
Hi @MiSNemesis
The recommended firmware version for ICX 7150 Switch is SPS08095dufi.bin
Please follow the below guides to perform an upgrade to the code 08095g UFI and upgrade both partitions with the switching code file named SPS08095gufi.bin to avoid the issues in future.
1.Upgrade a Switch ICX-7150-C12P using a USB flash drive
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-using-a-USB-flash-drive/td-p/46781
2. Upgrade a Switch ICX7150-C12P via TFTP
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-via-TFTP/m-p/47187
3. Upgrade a switch via Web GUI (ICX7150 Switch)
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-via-Web-GUI-ICX7150-Switch/td-p/48200
Please let us know if you have any queries in this regard.
Best regards,
Jayavidhya
Lennar Home Community
08.0.90BT211 (SPS08090d.bin) - I found this Compressed Pri Code version. This was under Compressed Sec Code 08.0.90BT213 (SPR08090d.bin)
ICX7150-C12 Switch
SSH@ICX7150-C12 Switch#show verCopyright (c) Ruckus Networks, Inc. All rights reserved.UNIT 1: compiled on Sep 22 2019 at 23:54:26 labeled as SPS08090d(28660224 bytes) from Primary SPS08090d.bin (Non-UFI)SW: Version 08.0.90dT211Compressed Primary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)Compiled on Thu Jan 31 03:08:55 2019
HW: Stackable ICX7150-C12-POE==========================================================================UNIT 1: SL 1: ICX7150-C12-2X10GR POE 12-port Management ModuleSerial #:FEK3203P15KSoftware Package: BASE_SOFT_PACKAGECurrent License: 2X10GRP-ASIC 0: type B160, rev 11 Chip BCM56160_B0==========================================================================UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module==========================================================================UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module==========================================================================1000 MHz ARM processor ARMv7 88 MHz bus8192 KB boot flash memory2048 MB code flash memory1024 MB DRAMSTACKID 1 system uptime is 121 day(s) 20 hour(s) 55 minute(s) 13 second(s)The system started at 06:39:31 GMT-05 Sat Mar 11 2023
The system : started=cold start
================================================================================ ===================== WARNING: FI image is not booted from UFI!!! ========= ============ Please download UFI image and reboot the system for full functionality ======================================================================================
Not sure what to do here now.
Greetings!!!
Thank you for the response and the update.
As I can see from the details you shared, your Switch is on the SPS08090d.bin Version.
Now please get the file SPS08095gufi.bin in place 08095hufi.bin (mentioned in the guide) file downloading it from the portal (Please refer to the below screenshot).
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-via-TFTP/td-p/47187
SPS08095gufi.bin – Pending
Please follow the below commands as mentioned in the above guide as well:
“copy tftp flash <tftp ip address> SPS08095gufi.bin primary” - (upgrade the image)
“Show flash” - (check the primary flash has the new code)
“Write memory” - (save the changes)
“boot system flash primary” - (boot the Switch with the new code)
After the Switch comes back, run the next final command to copy what is in the primary partition to the secondary because we need that both partitions match.
"copy flash flash secondary" - (will copy what is in the primary)
Please let me know if you have any queries in this regard.
Thank you again for your patience and understanding.
Imran Sanadi
RUCKUS Lennar Home Community.
SSH@ICX7150-C12 Switch>show flashStack unit 1:NAND Type: Micron NAND 2GiB (x 1)Compressed Pri Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)Compressed Sec Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)Compressed Pri Boot Code size = 786944, Version:10.1.26T225 (mnz10126)Compressed Sec Boot Code size = 786944, Version:10.1.26T225 (mnz10126)Code Flash Free Space = 1111314432SSH@ICX7150-C12 Switch>
Looks like the Flash update worked. Only issue now after the reboot is that some of my network cables on the switch are working. My 2 APs are not powering on at all.
