My Rukus is not broadcasting any internet and there is no power in my AP's after a power outage. I tried to reboot and also tried the reset with connection to the console but no luck. I cannot upload pictures. Can you please help.
i have solid green on SYST and PWR. The AP's are connected on POE 1 to 3 and the ethernet for the internet is connected to POE 4.
Hi @asitsinghal
Greetings!!!
Thank you for contacting RUCKUS Lennar Home Community.
Hope you are doing well!!!
Thank you for the information you shared.
As per the case description, I could understand that your RUCKUS setup is not working, and Access Points do not have power after a power outage.
"TFTP session timed out" message appears because the switch is looking for a TFTP server to load the configuration file from the TFTP server but there is no response from the TFTP server so for that reason creates a time out.
You can ignore this message if you are not going to download a configuration file from the TFTP server.
1. Here TFTP is not recommended. Sometimes we may need TFTP to Upgrade the switch via TFTP. And for now, we could disable it to prevent those continuous messages on CLI.
Please perform the below commands:
ICX7150-48ZP Router>enableNo password has been assigned yet...ICX7150-48ZP Router#config terminalICX7150-48ZP Router(config)#tftp disable
2. As you have console access, please perform the below commands, and send us the output for the same.
Note: Hit Enter to accept each command
enable
show versionshow inline power show inline power detail
3. If you want "TFTP session timed out" message disappears you can disable TFTP as mentioned above but you will not be able to do upgrades via TFTP you will have to re-enable it back as mentioned below:
ICX7150-48ZP Router>enableNo password has been assigned yet...ICX7150-48ZP Router#config terminalICX7150-48ZP Router(config)#no ftp disable
Please share the output of the above commands from point number 2 and let me know if you have any queries in this regard.
Thank you again for your patience.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
Please
see attached..
Can you please confirm if the modem ethernet connection is in the correct port.. I currently have it connected to Port 4 of the 12 ports.
Thank you for the information you shared,
As I can see from the information you shared, the PoE is in the disabled state on all the ports of the Switch (Please refer to the below screenshot). By which the Access Points are unable to get the power.
To enable the PoE on the Switch, please perform the below commands from the CLI:
Switch>enableNo password has been assigned yet...Switch#configure terminalSwitch(config)#interface ethernet 1/1/1 to 1/1/12Switch(config-mif-1/1/1-1/1/12)#inline power
Also attaching a Screenshot below as a reference:
Once you perform the above process all ports should be On, and APs should get the power.
To avoid these issues in the future, I would like to suggest upgrading your Switch to the latest stable version, as your current Switch is on the old version which is SPS08061a. Please let me know once you are done with the above process, to assist you with the upgrading of the Switch.
Please let me know if you have any queries in this regard.
NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS.
I have it running now!! thank you so much for your help.
Can you please assist me with the upgrade of the switch. Thank you !
Internet is back up and running. Just need your help with the upgrade of the switch!!
Thank you so much for your help
I've reviewed the and tried the information you have previously given to others, but the issue with my Ruckus is that there are no lights at all showing. I have tried to reset, I have unplugged it and waited and plugged it back in. This all occurred after a power outage, but it looks like my system never came back on so none of devices plugged into it are working now. I have followed the instructions to plug in a usb c but nothing works. I think it may have blew a fuse or something. What do I need to do to get a replacement system. Also the Ruckus Access point is not working either...no lights at all. Please help.
Hello Imran Sanadi
Can you please give instructions to upgrade the software.
Thank you.
"To avoid these issues in the future, I would like to suggest upgrading your Switch to the latest stable version, as your current Switch is on the old version which is SPS08061a. Please let me know once you are done with the above process, to assist you with the upgrading of the Switch."
Thank you for the response and the information you shared.
Great!!! Good to know that the Access Point power issue is now resolved.
Please follow the below steps to Upgrade your Switch to the latest stable version.
The recommended stable versions are 8095g (08.0.95g) or 8095j (08.0.95j)
The Upgrade path would be 8060>>8080f>>8095g OR 8095j
Below are the options or methods to perform the Upgrade on the switch: You could choose any one of these.
1st Option:
1. In this option, we will use a pen drive or USB flash drive in which we move the files to the pen drive and connect it to the Switch then through CLI we execute the commands to upgrade the Switch using the following guide as a reference:
How to Upgrade a Switch ICX-7150-C12P using a USB flash drive
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-using-a-USB-flash-drive/td-p/46781
2nd Option:
2. The following guide is an example of an upgrade via TFTP server, by using an application (FREE) to send files or upload remote files to a device, in our case, we will use it to update a new version to the Switch, basically it will send the image version remotely from the computer to the switch.
How to upgrade a Switch ICX7150-C12P via TFTP
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-via-TFTP/td-p/47187
3rd Option:
3. In this option we Upgrade the Switch from the Web Interface (GUI) of switch.
https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-via-Web-GUI-ICX7150-Switch/td-p/48200
Try to access your switch from a web browser by pasting the below URL in http or https form whichever that works.
https://0.0.0.0 or http://0.0.0.0 (IP address of Switch. 0.0.0.0 is just as an example)
As you can access CLI, I would suggest you follow the 2nd option.
Hi @Kai
Hope you are doing well
As this case is raised by @asitsinghal
To avoid confusion with posts, you can create your own post with the problem you're facing and a detailed description of the network issue and what you've done so that we can guide you properly.
Thank you again for understanding.
We’re literally having the same issue.
As mentioned before, this case is raised by @asitsinghal
