nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

R510 AP wrong address

unknown

Recently moved into a Lennar home with the Ruckus switch and two r510 ap's. I was attempting to change the AP's to have 192.168.2.0 to provide out. Initially both AP's were 192.168.1.0. I also have Spectrum AP where its set also to 192.168.1.0. The issue is I'm not able to change the the AP's IP. I've done the following - Changing to the .2.0 AP though I'm getting a 1.0 ip. I change to a 2.0 in order to access the AP which originally was 192.168.1.233. I assigned it to 192.168.2.233. When I manually change my pc's IP to 192.168.2.10 and ssh into the AP's 2.233. I do a get ipaddr wan and see the static vlan1 show as 192.168.2.233 255.255.255.0 192.168.2.1 . I then do a set ipaddr wan vlan1 192.168.1.233 255.255.255.0 192.168.1.1 . It reboots but never changes .

Find more posts tagged with

Accepted answers

All comments

syamantakomer

Hi Tim,

Is it the master AP on which you are trying to change IP? If yes, please do it from GUI.

And what is the Unleashed version? If it is not on 200.10, then it will not support VLAN tagging.

unknown

The one I changed through the GUI initially was not the Master AP. The version is 200.9 - I see the option to upgrade both 200.10 . Will this allow me to re-configure the IP on the 2nd AP?

syamantakomer

Hi Tim,

I have never tested but it is advised to change the master AP config from GUI and for member APs you can use GUI or CLI.

Starting from 200.10, you can use management VLAN for master and member APs, to keep the client traffic separate from AP management.

unknown

Image_ images_messages_60c92f6a22f33063d33be60a_40ce7916d31d182ae2064d50b033cb1f_C9E0B7BFCF864EE89D654365366972-680d4898-7617-46e4-acbd-712f51f2c5b9-1149943998.png

This is the AP Where I used to be able to change the IP

On this screen below - If I change to the 192.168.2.0 network will it give me access again to both AP’s

Image_ images_messages_60c92f6a22f33063d33be60a_6a95eed3e070e4313c9b4a82e48a7c3c_75B7A2BD5B3B4CC6847D9ED027C9E2-2f9f5631-b26a-488a-9a46-9d3e38be5792-1853100631.jpeg

Lastly this is what I see in the unleashed.ruckus site. Since I changed the IP It shows disconnected. Is there a way to unplug the POE so it can revert to the 192.168.1.0 network similar to a factory reset?

Image_ images_messages_60c92f6a22f33063d33be60a_40a7176c889f7408bc138d674b78ac35_46760A6A49FD4ED694CA473EAAA693-f6bdcefa-767c-458b-886f-c3028b705363-880237209.png

hayward_kong

Tim_Smith,

What are you trying to do?

From what I understand, you have one of the ISP provided modem/combo router right from Spectrum and you hooked it up to the Ruckus ICX switch and have the Ruckus R510 APs in a Lennar Home.

You can have the spectrum modem/combo/router to continue handing the routing, but with Wifi turned off and let the Ruckus R510 APs handle the wifi portion. Your spectrum Router will be the DHCP server and hand out all the IPs to your wifi clients though Ruckus APs. There is no reason the change the IPs of your Ruckus APs and have it hand out a different subnet than your spectrum combo router since the spectrum router doesn't handle different VLANs.

Make sure you did the typical setup for the Ruckus APs and not use them in gateway mode. The Ruckus APs will just be APs and no routing is involved while the Spectrum modem/combo router will handle the routing and DHCP address assignments with wifi turned off on the combo routing.

unknown

The plan was since I had both Spectrum wireless router and the Ruckus AP's was to designated the Spectrum as my IOT hand out and the Ruckus as my main ie laptop's desktops access etc. Since the switch looked like is was handing out IP's to the two AP's. both Ruckus and Spectrum were 192.168.1.0 which will work but is very sloppy management wise. So I was attempting to change the IP's of both routers to have Ruckus on a 2.0 subnet and spectrum handing out 1.0 network.

At this point I'd like to put everything back to what it was as I can now only access the one AP via ssh to the IP and it won't accept being put back on dhcp. My thought now is that the switch is Layer 2 and only providing POE.

unknown

I was able to put everything back - Had an old wireless router that was configured to 192.168.2.0 network. I plugged the ICX Switch in - everything grabbed the 2.0 IP. went to the AP that was on the 2.0 edited in and changed it from Keep AP Setting to DHCP- Plugged everything back - Now All AP's and Switch are talking as normal. Need to learn more on these devices before I play again.