nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

Ruckus R710 Low Power Alert

unknown

I have 3 brand new Ruckus R710 deployed in an office of 25 users.
I have a Netgear GS324PP powering them, and have used the same set up before but for some reason I'm seeing alerts on each WAP showing that it's not getting enough power, but the requirements show that it only needs 25W to function. My switch is POE+ so it's putting out 30W per port for them.

Has anyone else had this issue before?

Find more posts tagged with

Accepted answers

All comments

unknown

How does the netgear advertize power to the APs? Also, does the Net gear show to be overdrawn at all? have you moved the ports away from each other (i.e ap in port 1, ap in port 12, ap in port 24). Years ago we had Cisco switches which would fail to provide proper power if you "grouped" your high consumers on the same group of ports (1-12).

unknown

There's no alert showing that the switch is over drawn. I did however find that Ruckus reccomended a POE injector that was 60W, but I wanted to see if anyone else had the same issue before or had to purchase the POE injectors at twice the wattage that the WAPS say they need to run

vesalius

Check the recent thread below. The first post and probably the last couple might help.

Not enough electricity power provided with AP warning?

unknown

How Interesting. I spot-checked a few APs and see that I'm running 25w per AP. The ap reports no problem and has plenty of power. the AP and switch negotiated Power via LLDP.

Have you checked the cable runs by chance? the further they're run, the more power is lost to the AP.

To answer your question, yes, I have purchased POE injectors where I'm unable to feed them properly with the switches on site. Typically I use StarTech 4 port injector and do know that the unit cannot provide AT on all 4 ports reliably( but should work well for your need to power 3 APs).

https://www.amazon.com/StarTech-com-Port-Gigabit-Midspan-Wall-mountable/dp/B00VRESOW4

eth0
161 days, 17:40:03
XXX_XGIG-73907
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(3)E, RELEASE SOFTWARE (fc4)
70:e4:22:93:5f:xx
192.168.1.1
Bridge, on;Router, off
***RUCKUS b6a0***
Gi1/0/6
PSE
class 4
25000
25000

unknown

LLDP is always the reason!

michael_brado

I was going to suggest one AP into each of the 3 8-port sections of the Netgear switch, just to spread the load, from the past experiences Andrew recalled above.

unknown

I tried doing that and it didnt work. I actually have the last AP on its own switch but they all say that they have low power. I did see that Andrew had no issues running the APs with the startech which at most gives 30W.

unknown

Sorry LLDP is the reason why it works? I'm very green when it comes to networking, which is why I'm having issues with this.

vesalius

If this is unleashed, Did you go into the web GUI and change the POE setting for each AP from the default AUTO to 802.11at?

unknown

I am seeing the same issue on my R710 running off a Cisco RV350p which is PoE+. Never had this issue until I noticed it this week... shortly after upgrading firmware to 200.8.10.3.243. Tried to force 802.3at through ssh commands to R710 but still showing power is at af level. This is not the only firmware issue I'm seeing with Ruckus products. Has been my go to for network installs, but I cannot move forward with them until I see more consistent firmware upgrades that don't cause problems.

justauser

What was the resolution to this? It does sound like a firmware issue but the latest firmware as not resolved it.