BACK TO SUPPORT PORTAL
RUCKUS Technologies
Wired
Wireless
Cloud Services
Miscellaneous
RUCKUS Lennar Support
Lennar Knowledge Base
RUCKUS Lennar Support
Resources
Community
Technical
Register
RUCKUS Technologies
Home
RUCKUS Technologies and Products
Access Points - Indoor and Outdoor
P300 Communication Status in SCADA
unknown
I am using P300 Root and Non-Root bridges. I need to take the communication status and the signal strength in the SCADA(Wonderware Intouch) without logging in the browser. Please suggest an solution for this!!!!!!!!
Find more posts tagged with
Accepted answers
All comments
syamantakomer
Hi Vaitheeswaran,
If your SCADA system supports SNMP integration then you can use it to pull the stats from P300.
Here is the link for P300 MIB file which you have to add in your server and setup SNMP.
https://support.ruckuswireless.com/software_downloads/983-zoneflex-p300-ptmtp-ap-bridge-mibs-for-version-100-1-0-9-43-ga-software-release
Make sure that you enable SNMP on P300 bridge as well.
Regards,
Syamantak Omer
sanjay_kumar
Hi Vaitheeswaran,
If you want to use SNMP, try with the below OIDs.
WLINK RSSI : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.11
WLINK Uptime : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.10
WLINK Role : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.2
unknown
Hello Syamantak,
I am using Wonderware Intouch Software as SCADA. It supports SNMP Integration, Please check the below link it's for configurating the Bridges with Wonderware using System Management Console. I need to take the Connection Status( Whether the bridges are connected or not) and Signal Strength of the Bridge as a graphical representation. Please guide me how to take the datatype for the Connection Status and Signal Strength.
https://www.logic-control.com/datasheets/1/Device%20Connectivity/OI%20Servers/SNMP%20OI%20Server%20User%20Guide.pdf
syamantakomer
Hi Vaitheeswaran,
As suggested by Sanjay in his previous comment, please use below SNMP OIDs to pull the required details.
WLINK RSSI (Signal Strength) : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.11
WLINK Uptime (Connection status): .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.10
WLINK Role : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.2
Let us know if that answers your query or you have any further queries.
Regards,
Syamantak Omer
unknown
Hi Syamantak,
Is there any User Interface Protocol for Ruckus P300, so that i could access the signal status and strength by calling through the datatypes in my SCADA.
Thanks and Regards,
Vaitheeswaran Elango.
syamantakomer
Hi Vaitheeswaran,
I think you have already asked this on a different forum post and my colleagues Michael Brado already answered it.
https://forums.ruckuswireless.com/ruckuswireless/topics/p300
There is no HMI interface available in P300, all you can do is pull the SNMP data by setting up SNMP server on your SCADA (if supported) and configure the server details in P300. Rest data processing for graphical representation needs to be done on server side.
Regards,
Syamantak Omer
Quick Links
🗂️ All Categories
📄 Recent Posts
❓ Unanswered
🆘 Help
Tags
SmartZone or vSZ
RUCKUS Self-Help
Cloudpath
ICX
AP Management
vSZ
Access points
ICX Switch Management
Lennar homes
SmartZone
