nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

Ruckus AP Not Connecting After Reset

Akhen

Hi all,

I restarted my Master Ruckus AP because my network’s performance was having issues, and it seemed like the Ruckus APs might have been the issue. After the Master AP restarted and came back online, the other AP that’s meshed disconnected from the network, and I’m having a lot of trouble reconnecting it to my network.

I had to reset it with a paperclip, and I only got the Wizard to show up once, and have reset it again multiple times, and it seems stuck on “Building the Unleashed Network. It may take a few minutes.” now, so I feel stuck at this point. Also, right now it’s plugged into the switch my Master AP is on.

What are the exact steps to get the other AP reconnected to my network?

Thanks

Find more posts tagged with

Accepted answers

All comments

imran.sanadi@commscope.com

Hi @Akhen
Greetings!!!

Thank you for contacting the RUCKUS Community forums.

Before we assist you, could you please let me know if this is a Lennar Home RUCKUS setup?

Please confirm.

Thank you again.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Akhen

Hi Imran, yes, thanks.

imran.sanadi@commscope.com

Hi @Akhen

Greetings!!!

Thank you for your response and the confirmation.

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that you are encountering issues with the internet connectivity via RUCKUS devices.

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

To better assist you, could you please provide the following information:

1. Can you confirm if your RUCKUS setup was previously operational, and if there were any power outages before the issue began?
2. When your switch is connected to the outlet, do you observe any illuminated lights (amber or green)? Kindly describe which lights are visible. Additionally, please provide a photo showing the status of the lights and the full switch panel with cable connections to the switch ports.

3. How many access points are currently connected to the switch? Please describe the status of the lights on the access points. Similarly, include a photo showing the access points' light status.

Please log into your RUCKUS Account before uploading these photos/screenshots.

Please help me with ALL requested queries, and should you have any further questions or concerns, feel free to reach out.

We appreciate your cooperation and look forward to resolving this matter for you promptly.

Best regards,

Imran Sanadi
RUCKUS Lennar Home Community

imran.sanadi@commscope.com

Hi @Akhen

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it. Please help me with the requested queries.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

Akhen

Hi Imran,

Thanks for your help.

The Ruckus setup was previously operational, and there were no power outages before the issue began. There were network performance issues as I mentioned in my initial post, so I restarted the Master AP. The Unleashed Dashboard indicated that the “network was rebuilding”, then the Master AP came back online, but the Meshed AP wasn’t connected to the network. I tried for quite awhile to figure out what the issue was, but eventually I had to reset the Meshed AP with a paperclip, as I posted above, and that’s where I got stuck.
I’ll attach a photo of the Ruckus ICX-7150-C12P Switch. There shouldn’t be any issues with the Switch.
There are 2 APs currently connected to the Switch: the Master AP, and I also plugged the Meshed AP into the Switch, since I was hoping it would be picked up by the network, so everything could go back to normal, but as of now I’m having issues with that. The Meshed AP has the PWR light solid, and the CTL light blinking, since I reset it with a paperclip.

If I need to SSH into the Meshed AP to resolve this issue, please provide the steps to do so. I’m running Windows 11.

Thanks again for your help. Ruckus R610 Lights.jpg Ruckus ICX-7150-C12P Switch Lights & Connections.jpg