nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

Cannot Connect with ICX 7150-C12P and Two R510 AP

lc578

Hi,

When I moved into my home, it came with various smart home features including the Ruckus setup as noted in the title. Recently, the two R510 AP that are downstairs and upstairs have not been showing the LED lights. I have tried unplugging the PoE ports from both, resetting for 15 and 30 seconds, but no success; no light will not turn on.

As a result, I have been following the guide in this post by Vasquez Far to update the ICX and it has been going well until step 17:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-using-a-USB-flash-drive/td-p/46781

When I enter the code:

copy disk0 flash mnz10114.bin bootrom

the CLI results in infinite lines of code that says "PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power" even though the USB is plugged into the ICX correctly and the files on the USB are correct (I have to restart PuTTY to code again)

I tried searching online for answers but have not come across one that has effectively solved my problem. The closest I have reached to solving is through another post from the same person:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-7150-12CP-Ruckus-Switch/td-p/46759

However, I am having trouble with opening PuTTY with the correct COM (USB) port. Would appreciate some help on this issue as I cannot receive any power through both AP and cannot continue coding through the CLI without the above error.

Find more posts tagged with

Accepted answers

All comments

imran.sanadi@commscope.com

Hi @lc578

Greetings!!!

Thank you for reaching out to the RUCKUS Lennar Home Community.

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that you are encountering issues with the RUCKUS setup.

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

To better assist you, could you please provide the following information:

1. Can you confirm if your RUCKUS setup was previously operational, and if there were any power outages before the issue began?
2. When your switch is connected to the outlet, do you observe any illuminated lights (amber or green)? Kindly describe which lights are visible. Additionally, please provide a photo showing the status of the lights and the full switch panel with cable connections to the switch ports.

3. Please execute the following commands in CLI and provide the outputs:

enable

show version

show flash

show inline power

show inline power detail

show interface brief

Please log into your RUCKUS Account before uploading these photos/screenshots.

Please help me with ALL the above queries and should you have any further questions or concerns, feel free to reach out.

We appreciate your cooperation and look forward to resolving this matter for you promptly.

Best regards,

Imran Sanadi
RUCKUS Lennar Home Community

lc578

Hi Imran, thanks for the reply.

Yes my Ruckus setup was working previously. I cannot confirm that the issues stemmed from a power outage, but can assure you that there has been at least one since then.

The only lights I can see are the SYST, PWR, and wifi LEDs and they are all solid green. (yellow cable is connected to my AT&T modem and the blue cables are connected to the APs; I am not sure which cables are connected to either AP and no lights are shown for either blue cable)

Below are the results from the suggested commands in the CLI (PuTTY) accessed by the Telnet:

enable:

show version:

ICX_show version.jpg

show flash:

ICX_show flash.jpg

show inline power:

ICX_show inline power.jpg

show inline power detail (2 photos):

ICX_show inline power detail 1.jpg

ICX_show inline power detail 2.jpg

show interface brief:

ICX_show interface brief.jpg

imran.sanadi@commscope.com

Hi @lc578

Thank you for the response and the update.

This issue is mainly because of the older version on your RUCKUS Switch.

Could you please try to upgrade your Switch using the below method (Upgrade using CLI)?

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-7150-C12P-via-TFTP/td-p/47187

Please let me know if you are stuck at any point during the Switch upgrade process.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community

lc578

Hi Imran,

As I was going through the steps in the link, I came across a problem when trying to copy the mnz10114.bin file. Below is the instructions that I cannot get past as well as the error that follows. I have already searched for answers online but cannot find any. The error is "TFTP to Flash Error - code 5"