I tried to authenticate wispr using Ruckus cloud wispr page.

A form for POST is below.

document.write('<form method=POST action="https://' + get_sip() + ':443/SubscriberPortal/hotspotlogin">');

But it is not working.

How do I configure wispr page like SZ or RC style?

Regards.

Greetings from RUCKUS!

We’re glad to have you here! To make your experience smoother, we’ve created the RUCKUS Lennar Knowledge Base, a dedicated self-help section with step-by-step guides, solutions to common issues, and troubleshooting resources for your RUCKUS devices.

Before posting a new question, we kindly encourage you to:

1. Visit the RUCKUS Knowledge Base to check if your issue is already addressed.

2. Use the search bar or browse related content links to see if other users have discussed the same issue.

3. Join existing discussions where you can find valuable insights or share your experience.

If you don’t find a solution, please post your query in the RUCKUS Lennar Support section, and our team will be happy to assist you in resolving issues with your Lennar Home RUCKUS devices.

Thank you for being part of the RUCKUS Lennar Community, your contributions help make this space a richer resource for everyone!

It is pretty confusing because I can control both of them.

For ruckus cloud, APs can be in standalone mode ?

I have been experiencing the following symptoms for several weeks.

When I check the traffic information on the APs registered with vSZ-H, there are times when the values for traffic and number of connections are missing, as shown in the attached image.

As far as we have confirmed on site, there is no interruption in the same time, streaming, etc., and there is no problem with communication.

The first time I discovered this coincided with the timing of the firmware upgrade, so I thought that might be the cause, but I have no proof.

The current environment is as follows

Controller version 5.2.2.0.1563
Controller plane version 5.2.2.0.1540
AP firmware 5.2.2.0.2069 (R650)

Please let me know if you have similar symptoms or know of any possible causes.

Sincerely yours.

Can you confirm that I have upgraded my switch to the best and latest version possible?

I have followed all of your steps and want to make sure that I have upgraded the switch properly so that I can avoid future issues as the switch registers as a "router" vs a switch every few months and I hate it.

Can you also please confirm how and when I'm supposed to upgrade it? How am I supposed to know when a new version is out and when it's time to upgrade it?

Please use the details below to confirm if I am now running the best possible version needed to help with all of the issues I constantly experience:

SSH@ICX7150-C12-Switch#show version

Copyright (c) Ruckus Networks, Inc. All rights reserved.

UNIT 1: compiled on Sep 22 2019 at 23:54:26 labeled as SPS08090d

(28660224 bytes) from Secondary SPS08090d.bin (UFI)

SW: Version 08.0.90dT211

Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)

Compiled on Thu Apr 21 06:08:52 2022

HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

Serial #:FEK3849RBF6

Software Package: BASE_SOFT_PACKAGE

Current License: 2X1G

P-ASIC 0: type B160, rev 11 Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8192 KB boot flash memory

2048 MB code flash memory

1024 MB DRAM

STACKID 1 system uptime is 2 day(s) 22 hour(s) 6 minute(s) 53 second(s)

The system started at 21:58:26 GMT+00 Fri Jan 07 2000

The system : started=warm start reloaded=by "reload"

SSH@ICX7150-C12-Switch#flash

Incomplete command.

SSH@ICX7150-C12-Switch#show flash

Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)

Compressed Sec Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)

Compressed Pri Boot Code size = 786944, Version:10.1.24T225 (mnz10124)

Compressed Sec Boot Code size = 786944, Version:10.1.24T225 (mnz10124)

Code Flash Free Space = 1107275776

SSH@ICX7150-C12-Switch#

We also had a non-EAP network with captive portal becaude some users have problems with EAP (like incompatible devices). I don't see how to implement a wifi network with captive portal authenticating on a LDAP or AAA server.

Do I need to use (and install) a WISPr portal ?

Thanks.

Can the t750se signal be extended beyond default signal strength thru an external antenna?

The ZD1200 sees the new R510 AP and says it is connected and has an IP of 10.34.14.74

The switch port for the new ap are 2UP and the ZD1200 can see it. If I change this to the same port settings as the other AP's then the ZD1200 cannot see it. 

The new AP shows    VLAN 2 10:f0:68:3e:6d:40 GE1/19 in the switch MAC addr table

The working AP's have a switch port with 2T, 14UP, 60T, 70T. 

Pic of AP T300 showing VLAN 2

Pic of R510 showing VLAN 1

We use SmartZone V 5.2.1.0.515
On there we have our switches (majority of them are the ICX 7150)
I am trying to use the  5.2 Switch API to set the "rate-limit" input and output on a port, however, I am not finding this as an option in any of the documentation. 
Can anyone verify if this is available to do through API call, and if so, can you point me towards the documentation so I may utilize it.

Thank you

Bob

When  I set up the WPA3+DPSK with the RUCKUS® R760, do clients have to bind MAC address? If not, what distinguishes different clients?

Thanks.

 https://www.businesswire.com/news/home/20230119005140/en/RUCKUS-Networks-Enables-Multi-Dwelling-Units-to-Access-New-6-GHz-Spectrum-Enhancing-Advanced-Wi-Fi-Services