topic Re: QoS Settings not persisting across reboots in Unleashed

QoS Settings not persisting across reboots

Rucky860 — Wed, 13 Dec 2023 16:11:15 GMT

The other day I ran the following commands on my R650s with Unleashed 200.14.6.1.203:

enable
ap-mode
set qos igmp_query v2 enable
set qos igmp_query v3 enable
set qos mld_query v1 enable
set qos mld_query v2 enable
set qos eth0 mld enable
set qos eth1 mld enable
set qos eth0 directed multicast disable
set qos eth1 directed multicast disable
set qos directedRA disable
set qos directedDHCP disable
set qos forward_querier enable
quit

After both APs are rebooted, the following settings are NOT persisted:

get qos:

IGMP General Query V2/V3: Disabled/Disabled
MLD General Query V1/N2: Disabled/Disabled

get qos eth0/eth1:

Directed Multicast: Enabled

MID Snooping Mode: Disabled

Re: QoS Settings not persisting across reboots

Rucky860 — Wed, 13 Dec 2023 20:20:22 GMT

Bump.

Re: QoS Settings not persisting across reboots

Rucky860 — Wed, 20 Dec 2023 14:12:14 GMT

This issue is very repeatable. I power cycled both R650s and some QoS settings (in original post) are lost. This clearly seems to be a bug. Can someone from Ruckus comment?

Re: QoS Settings not persisting across reboots

Rucky860 — Wed, 20 Dec 2023 14:13:15 GMT

@8vin Any thoughts?

Re: QoS Settings not persisting across reboots

Rucky860 — Sun, 31 Dec 2023 02:00:32 GMT

Can anyone help here? Seems like broken firmware.

Re: QoS Settings not persisting across reboots

syamantakomer — Thu, 04 Jan 2024 16:08:41 GMT

Hello @Rucky860,

You are making these changes from AP mode, which cannot survive the reboot.

Let me ask one of our team members to verify if there is a way to do it and get back to you.

Re: QoS Settings not persisting across reboots

sanjay_kumar — Thu, 04 Jan 2024 16:21:54 GMT

@Rucky860

I'm checking this in lab and I should be able to provide you with an answer shortly.

Re: QoS Settings not persisting across reboots

sanjay_kumar — Thu, 04 Jan 2024 16:50:48 GMT

Hi @Rucky860

I have checked this in lab with the same version, and I can see that the below settings are not persistent as you mentioned.
IGMP General Query V2/V3
MLD General Query V1/N2

Let me check more on this and update you with the root cause.

Re: QoS Settings not persisting across reboots

sanjay_kumar — Fri, 05 Jan 2024 08:18:38 GMT

Hi @Rucky860

I found the reason, the config changes which you are making is from the "ap-mode" which is not exactly the Master CLI mode but the AP CLI mode.
After making the changes, it will hold the config, but in fact it will saved as AP config and not in Master config. To save the config in the Master the settings as to be from the "Config" mode rather than the "Ap-mode".

So once the AP reboots, the AP config will override based on the Master config. Which is why the settings made from the ap-mode prompt is not saving.

Re: QoS Settings not persisting across reboots

sanjay_kumar — Thu, 11 Jan 2024 03:30:16 GMT

Hi @Rucky860
Let me know if you have any further queries on this.

Re: QoS Settings not persisting across reboots

vesalius — Thu, 18 Jan 2024 01:51:59 GMT

@sanjay_kumar @syamantakomer Unless I am doing this wrong, Once in the config mode on the Master (not ap-mode), then 'set' is not a valid command.

Welcome to Ruckus Unleashed Network Command Line Interface ruckus> enable ruckus# config You have all rights in this mode. ruckus(config)# set qos eth0 mld enable The command is either unrecognized or incomplete. To view a list of commands that you can run from this context, type '?' or 'help'. ruckus(config)#

Re: QoS Settings not persisting across reboots

Rucky860 — Thu, 18 Jan 2024 01:31:09 GMT

I've since migrated my APs to Ruckus One, so I can't re-test with your additional information. I do appreciate the response though.

Re: QoS Settings not persisting across reboots

sanjay_kumar — Mon, 22 Jan 2024 03:23:03 GMT

Hi @vesalius
This is a WLAN mode command, try the command as below:

Please login: admin
Password:
Welcome to Ruckus Unleashed Network Command Line Interface
ruckus> en
ruckus# config
You have all rights in this mode.
ruckus(config)# wlan testing
The WLAN service 'testing' has been loaded. To save the WLAN service, type 'end' or 'exit'.
ruckus(config-wlan)# qos mld-snooping
The command was executed successfully. To save the changes, type 'end' or 'exit'.
ruckus(config-wlan)#

Re: QoS Settings not persisting across reboots

vesalius — Mon, 22 Jan 2024 23:59:44 GMT

Ok thanks. That changes the values for the Wlan, how about eth0/1?

Re: QoS Settings not persisting across reboots

sanjay_kumar — Tue, 23 Jan 2024 04:21:55 GMT

Hi @vesalius

For ethernet port, it has to be entered in the ap-group level. Below is an example

ruckus(config)# ap-group "System Default"
ruckus(config-apgrp)# model h510 port-setting
ruckus(config-apgrp)# show
ruckus(config-apgrp)# lan 2 qos mld-snooping

Re: QoS Settings not persisting across reboots

vesalius — Tue, 23 Jan 2024 12:54:02 GMT

This is what I have used on prior firmware versions, but no longer works for r650 and/or r750. Seems like the h510 is one of the few that still does in either 200.14 or 200.15.

ruckus(config)# ap-group "System Default" ruckus(config-apgrp)# model r650 port-setting ap_name: r650 The model could not be configured in unleashed. ruckus(config-apgrp)# model r750 port-setting ap_name: r750 The model could not be configured in unleashed. ruckus(config-apgrp)#

Re: QoS Settings not persisting across reboots

koatic — Tue, 13 Feb 2024 14:44:30 GMT

We have same issue and cannot configure the AP-group mode to persist reboots.

firmware 200.15.6.12.304

ruckus(config-apgrp)# model r550 port-setting
ap_name: r550
The model could not be configured in unleashed.
ruckus(config-apgrp)#

Any update on this issue???

Re: QoS Settings not persisting across reboots

Rucky860 — Fri, 16 Feb 2024 13:58:41 GMT

I'm now on Ruckus one, but curious if Unleashed will get fixed?