https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4656#M266 What does it say when you type 'get version' at the AP CLI prompt, that is the image that is running.<BR /><BR />Type 'get director' and 'get scg' to determine if SCG service is running, which means the AP thinks it's under SCG control.<BR /><BR />A factory default and WebUI access, is recommended to "upgrade" firmware to a Solo/Standalone image, if not on the 100.x code now. Tue, 10 Oct 2017 18:28:59 GMT michael_brado 2017-10-10T18:28:59Z https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4652#M262 I installed the unleashed software in a R500 and was testing it. <BR /><BR />I now want to revert the software back to 100.x.x.x.x but I cant seem to get it to revert to factory like when its originally at 100.x.x.x.x then its taken over by a ZD and changes it to 9.12.x.x.x. <BR /><BR />In this configuration I just press the reset button for 10 seconds then I can http to the unit and install the 100.x.x.x. software.<BR /><BR />When I do it with the unleashed it just resets to unleashed and I cant load a different software ...<BR /><BR />Any help would be appreciated ..<BR /><BR /><BR />Thanks Tue, 20 Oct 2015 13:43:02 GMT https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4652#M262 cristian_salce1 2015-10-20T13:43:02Z https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4653#M263 Hi Cristian, <BR /><BR /> You just have to hard reset the AP. <BR /><BR /> Once the hard reset is done, the setup wizard appears again. There click on "Show AP Info" and we can see the Upgrade option to upload firmware. <BR /><BR /> Downgrade the AP to 100.x ZoneFlex based image version for that model of Access Point. <BR /><BR /> - Anusha Vemula Tue, 20 Oct 2015 13:46:59 GMT https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4653#M263 Anusha_Vemula 2015-10-20T13:46:59Z https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4654#M264 Answered my own question..<BR /><BR />on the welcome screen after button reset press the sh ap info button then upgrade button. this will give you the option to upload the 100.x.x.x. file to the AP.... Tue, 20 Oct 2015 13:47:31 GMT https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4654#M264 cristian_salce1 2015-10-20T13:47:31Z https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4655#M265 I have an almost the same problem<BR /><BR />I have an R500 and on confirming its version, it says<BR /><BR />### Active SW ###<BR />SW Version: 3.2.1.0.659<BR /><BR /><BR />While the SW images on flash says<BR />version: 100.0.0.0.127<BR /><BR />what is the difference of the two as I can see them both on my R500 Tue, 10 Oct 2017 03:44:02 GMT https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4655#M265 kim_justimbaste 2017-10-10T03:44:02Z https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4656#M266 What does it say when you type 'get version' at the AP CLI prompt, that is the image that is running.<BR /><BR />Type 'get director' and 'get scg' to determine if SCG service is running, which means the AP thinks it's under SCG control.<BR /><BR />A factory default and WebUI access, is recommended to "upgrade" firmware to a Solo/Standalone image, if not on the 100.x code now. Tue, 10 Oct 2017 18:28:59 GMT https://community.ruckuswireless.com/t5/Unleashed/I-want-to-revert-my-Unleased-to-100-x-x-x-x/m-p/4656#M266 michael_brado 2017-10-10T18:28:59Z