topic Re: ICX7150 Upgrade in ICX Switches

ICX7150 Upgrade

ADIT — Fri, 16 Feb 2024 01:01:40 GMT

Hello, We have Six ICX7150 SW Running Image Version: 08.0.90dT213.

Can you tell me what version is recommended, and can it be updated directly to the latest version, or are there some required versions in between?

Thank you.

Re: ICX7150 Upgrade

BenBeck — Fri, 16 Feb 2024 02:06:43 GMT

8095m or 8095n would be my recommendation at the moment. You can also look at this:

https://community.ruckuswireless.com/t5/RUCKUS-Self-Help/What-code-should-I-run-on-my-ICX-Check-the-Recommended-Firmware/m-p/33612

You can upgrade direct.

Re: ICX7150 Upgrade

ADIT — Fri, 16 Feb 2024 05:12:31 GMT

Hi @BenBeck

Thanks for the response. We have downloaded the 8095m firmware. In the folder, I could see 2 files. Could you please check and share which file should we use for the upgrade. Attached screenshot for reference.Please ignore the VLC format

Re: ICX7150 Upgrade

Mayank — Fri, 16 Feb 2024 08:00:36 GMT

Hi Adit,

In the screenshot, I can see one is SPR8095mufi and another is SPS8095mufi here SPR stands for routing image and SPS stands for switching image.

So it depend on what type firmware you are using earlier if you are using a router code use SPR and if you are using switch code use SPS. You can find this by using show version command on your existing setup.

Moving Forward If this issue is not resolved , Please log a ticket with the below link so that we will help you further.

https://support.ruckuswireless.com/contact-us

I hope this information helps you

Please feel free to leave us a message if any concerns

Re: ICX7150 Upgrade

ADIT — Mon, 19 Feb 2024 05:04:15 GMT

Hi,

This is the current version details. Could you please check and recommend which version should use for upgrade.

SSH@RSH-STH-SW-02>sh ver
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Sep 23 2019 at 00:00:25 labeled as SPR08090d
(32539748 bytes) from Secondary SPR08090d.bin (UFI)
SW: Version 08.0.90dT213
Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz1011 5)
Compiled on Thu Jan 31 07:08:55 2019

HW: Stackable ICX7150-24-POE
==========================================================================
UNIT 1: SL 1: ICX7150-24P-4X1G POE 24-port Management Module
Serial #:FEA3238R0FT
Software Package: ICX7150_BASE_L3_SOFT_PACKAGE
Current License: 4X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-4X10GF 4-port 40G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 23 hour(s) 25 minute(s) 47 second(s)
The system started at 00:03:50 GMT+00 Sat Jan 01 2000

The system : started=cold start

Re: ICX7150 Upgrade

Mayank — Mon, 19 Feb 2024 06:05:35 GMT

Hi ADIT,

I can see that you are running on the SPR image which is the router image, Hence you need to upgrade to SPR only.

Thanks

Re: ICX7150 Upgrade

ADIT — Mon, 19 Feb 2024 06:53:34 GMT

Thank you for the help.

HW: Stackable ICX7150-24-POE - is this consider when selecting image file OR is it same for all ICX7150 models ?

Re: ICX7150 Upgrade

Mayank — Mon, 19 Feb 2024 07:17:34 GMT

While selecting between SPR and SPS image we don't consider that HW spec.

Thanks

Re: ICX7150 Upgrade

ADIT — Mon, 19 Feb 2024 08:33:28 GMT

Okai. Thank you so much for your help and instructions. Let me try to do the upgrade then.

Re: ICX7150 Upgrade

Mayank — Fri, 23 Feb 2024 08:47:45 GMT

Happy to Help 🙂

Re: ICX7150 Upgrade

ADIT — Tue, 26 Mar 2024 05:47:23 GMT

What is mufi in image file name?

SPR8095mufi