topic Re: Is there a command to check vlan tagged or untagged based on port in ICX Switches

Is there a command to check vlan tagged or untagged based on port

BusinessUser — Tue, 15 Aug 2023 04:37:30 GMT

In cisco, the configuration is displayed such that interface is displayed first and vlan tagging or untagging is secondary.

Is there a command in ruckus so that I check the vlan tagging based on port, especially for the show run?

Can I enter the vlan tagging after going into the interface first?

Re: Is there a command to check vlan tagged or untagged based on port

Zairah — Tue, 15 Aug 2023 06:56:07 GMT

Hello @BusinessUser ,

You can use " show vlan " command to check the tag and untag ports associated with particular vlan

Also you can tag /untag the port by going into the vlan and then using tag/untag command

#config

#vlan <>

#tagged/untag ethernet <>

Example :

! Management VLAN configuration.

SCH-ACCESS-101(config)# vlan 10 by port
SCH-ACCESS-101(config-vlan-10)# untag ethernet 1/1/1 to 1/1/4
SCH-ACCESS-101(config-vlan-10)# management-vlan
SCH-ACCESS-101(config-vlan-10)# default-gateway 10.10.10.1 1
SCH-ACCESS-101(config-vlan-10)# default-gateway 10.20.20.1 2

! User VLAN configuration.

SCH-ACCESS-101(config)# vlan 1011
SCH-ACCESS-101(config-vlan-1011)# tagged ethernet 1/1/13 to 1/1/17 ethernet 1/2/2 ethernet 1/2/4 ethernet 2/2/2 ethernet 2/2/4
SCH-ACCESS-101(config-vlan-1011)# untagged ethernet 1/1/12
SCH-ACCESS-101# show vlan 1011
Total PORT-VLAN entries: 14
Maximum PORT-VLAN entries: 64
Legend: [Stk=Stack-Id, S=Slot]
PORT-VLAN 1011, Name data_vlan, Priority level0, Spanning tree On
Untagged Ports: (U1/M1) 12
Tagged Ports: (U1/M1) 13 14 15 16 17
Tagged Ports: (U1/M2) 2 4
Tagged Ports: (U2/M2) 2 4
Uplink Ports: None
DualMode Ports: None
Mac-Vlan Ports: None
Monitoring: Disabled

For your reference below is the link of the guide which shows tagging and untagging part:

https://support.ruckuswireless.com/articles/000006352

Regards,

Zairah Javeed
Sr Technical Support Engineer | L2 TAC Wired
support.ruckuswireless.com/contact-us

COMMSCOPE
now meets next

Note: Please feel free to mark the post as ACCEPTED SOLUTIONS

Re: Is there a command to check vlan tagged or untagged based on port

BusinessUser1 — Wed, 16 Aug 2023 09:23:34 GMT

Can I start by going into the interface first?

Just like cisco int xxx, switchport mode access,

Re: Is there a command to check vlan tagged or untagged based on port

Zairah — Tue, 22 Aug 2023 02:14:46 GMT

Hi @BusinessUser1 ,

We can do other configurations by adding to interface but tagging and untagging can be done via vlan

Regards,

Zairah Javeed
Sr Technical Support Engineer | L2 TAC Wired
support.ruckuswireless.com/contact-us

COMMSCOPE
now meets next

Note: Please feel free to mark the post as ACCEPTED SOLUTIONS

Re: Is there a command to check vlan tagged or untagged based on port

BusinessUser — Tue, 22 Aug 2023 04:13:11 GMT

So I assume that the answer is no?

Re: Is there a command to check vlan tagged or untagged based on port

BenBeck — Tue, 22 Aug 2023 11:19:19 GMT

You can use something like 'show vlan brief eth 1/1/1' if you are specifically looking for vlan membership on one port.

Re: Is there a command to check vlan tagged or untagged based on port

Zairah — Wed, 23 Aug 2023 07:21:15 GMT

Hi @BusinessUser

You can use below commands to add vlans via interface .Please let us know if you are looking for this command.

int eth <>
vlan-config add tagged-vlan <>

And you can use show vlan brief eth <> if you are specifically looking for vlan membership on specific port.

Regards,

Zairah Javeed
Sr Technical Support Engineer | L2 TAC Wired
support.ruckuswireless.com/contact-us

COMMSCOPE
now meets next

Note: Please feel free to mark the post as ACCEPTED SOLUTIONS

Re: Is there a command to check vlan tagged or untagged based on port

Chandini — Wed, 06 Dec 2023 17:09:28 GMT

Hi Businessuser1

Thank you for reaching us. You can use the below command to view tagging and untagged details for single port.

Example below: Here we are seeing port 1/1/1 information

Command:

SSH@7150_switch_test(config)#show vlan brief ethernet 1/1/1

Output:

Port 1/1/1 is a member of 1 VLANs
VLANs 1
Untagged VLAN : 1
Tagged VLANs :

I hope the above information helps you

Thanks