topic Re: VSRP in switch ICX7150-C12P in ICX Switches

VSRP in switch ICX7150-C12P

Ayoubinho — Fri, 24 Feb 2023 10:08:11 GMT

Hello Everyone,

I'm configuring VSRP in two switches with licenses l3 validated, I want to make a virtual IP address for gateway to make redundance. I have followed in part the help here : https://docs.ruckuswireless.com/fastiron/08.0.60/fastiron-08060-l2guide/GUID-D9FB37DA-C043-42E3-BECC-031D762F54A3.html

But I cant enter the command router vsrp...

Please Help !

Re: VSRP in switch ICX7150-C12P

aalvarez6 — Fri, 24 Feb 2023 16:16:26 GMT

Hello,

You are currently running layer 2 code or layer 3 in the switch? Also, according to the guide, if you already have VSRP there is no need to re-enable it, what version are you using? You can enable VSRP per vlan in 8060 version but the form and instructions are different per version:

Optionally, globally enable the VSRP protocol.
This is required only if VSRP was disabled earlier and you want to re-enable it.

Re: VSRP in switch ICX7150-C12P

Ayoubinho — Mon, 27 Feb 2023 07:27:23 GMT

Hi,

I'm running layer 3 I think because I have this license : Current License: 2X10GR

Version : SW: Version 08.0.95fT211

But you did'nt understand what I need. I want to program a virtual IP but I can't.......

Re: VSRP in switch ICX7150-C12P

Ayoubinho — Mon, 27 Feb 2023 07:33:04 GMT

I think the question is, can I configure VSRP whith IP in a ICX 7150-c12p Switch ?

Re: VSRP in switch ICX7150-C12P

aalvarez6 — Mon, 27 Feb 2023 16:19:09 GMT

Hi Ayoubinho,

If I understood correctly here is the process that you need to follow:
https://docs.commscope.com/bundle/fastiron-08095-commandref/page/GUID-80C6BE08-19E0-4878-93C1-A1A732FDEBB4.html

If you are configuring a Layer 3 switch for VSRP, you can specify an IP address to back up. When you specify an IP address, VSRP provides redundancy for the address. This is useful if you want to back up the gateway address used by hosts attached to the VSRP backups. VSRP does not require you to specify an IP address. If you do not specify an IP address, VSRP provides Layer 2 redundancy. If you do specify an IP address, VSRP provides Layer 2 and Layer 3 redundancy.

The VRID IP address must be in the same subnet as a real IP address configured on the VSRP interface, but cannot be the same as a real IP address configured on the interface.

Failover applies to both Layer 2 and Layer 3.

The no form of the command removes the configured backup IP address.

Re: VSRP in switch ICX7150-C12P

Ayoubinho — Tue, 28 Feb 2023 07:49:14 GMT

SWITCH2VSRP#conf t
SWITCH2VSRP(config)#vlan 200
SWITCH2VSRP(config-vlan-200)#vsrp vrid 1
SWITCH2VSRP(config-vlan-200-vrid-1)#ip-address 192.168.1.25
Invalid input -> ip-address 192.168.1.25
Type ? for a list
SWITCH2VSRP(config-vlan-200-vrid-1)#ip-address 10.10.10.1
Invalid input -> ip-address 10.10.10.1
Type ? for a list
SWITCH2VSRP(config-vlan-200-vrid-1)#ip-address 192.168.1.253
Invalid input -> ip-address 192.168.1.253
Type ? for a list
SWITCH2VSRP(config-vlan-200-vrid-1)#
activate Activate VRRPE router
advertise Advertise this backup router to master
backup Configure as VRRPE backup router
backup-hello-interval Set VRRPE back router hello interval
clear Clear table/statistics/keys
dead-interval Set VRRPE dead interval
disable Disable VRRPE router
enable Enable VRRPE router
end End Configuration level and go to
Privileged level
exit Exit current level
hello-interval Set VRRPE advertisement interval
hold-down-interval Set VSRP master hold-down interval
include-port VSRP-only: Include additional ports from
VLAN
initial-ttl Set VSRP initial TTL value
no Undo/disable commands
non-preempt-mode Enable VRRPE non-preempt mode
quit Exit to User level
restart-ports VSRP-only: Set option to restart all VSRP
ports when Master becomes Backup
save-current-values Set VSRP to save current parameters value
show Show system information
track-port Configure VRRPE track ports
write Write running configuration to flash or
terminal
<cr>

Re: VSRP in switch ICX7150-C12P

Ayoubinho — Tue, 28 Feb 2023 07:51:01 GMT

I wanted to follow the instructions of the process that you sent me but I can't, I sent you commands that I type.

Re: VSRP in switch ICX7150-C12P

aalvarez6 — Tue, 28 Feb 2023 18:02:09 GMT

Hello,

Can you please share a show version and show flash with me?

Regards,

Ayleth Alvarez
Sr Technical Support Engineer | L2 TAC Wired

COMMSCOPE
now meets next

Re: VSRP in switch ICX7150-C12P

Ayoubinho — Mon, 06 Mar 2023 07:14:47 GMT

ICX7150-C12 Switch#sh version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Dec 16 2021 at 03:40:25 labeled as SPS08095f
(31457280 bytes) from Primary SPS08095f.bin (UFI)
SW: Version 08.0.95fT211
Compressed Primary Boot Code size = 786944, Version:10.1.21T225 (mnz10121)
Compiled on Wed Aug 25 06:27:49 2021

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3233T0HS
Software Package: BASE_SOFT_PACKAGE
Current License: 2X10GR
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 7 hour(s) 50 minute(s) 9 second(s)
The system started at 03:45:21 GMT+00 Thu Dec 16 2021

The system : started=cold start

Re: VSRP in switch ICX7150-C12P

Ayoubinho — Mon, 06 Mar 2023 07:16:12 GMT

ICX7150-C12 Switch#sh flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95fT211 (SPS08095f.bin)
Compressed Sec Code size = 33554432, Version:08.0.95fT213 (SPR08095f.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.21T225 (mnz10121)
Compressed Sec Boot Code size = 786944, Version:10.1.21T225 (mnz10121)
Code Flash Free Space = 1009766400