topic Re: Icx7250 firmware upgrade now no uplink ports live in ICX Switches

Icx7250 firmware upgrade now no uplink ports live

Richl — Wed, 15 Feb 2023 18:54:25 GMT

How can I enable the uplink ports from the console

Re: Icx7250 firmware upgrade now no uplink ports live

aalvarez6 — Thu, 16 Feb 2023 15:55:19 GMT

Hello,

Do you see any lights on the ports?
If not, then please enter this command with the port you want to check:
show inter ether x.x.x -affected port

Once you checked the port it should say UP, if it is down, please check that you set the right speed for the port, you can also change the speed like this:

Switch-to-AP(config)#inter ether 1/1/1
Switch-to-AP(config-if-e1000-1/1/1)#speed
speed-duplex Set to 100g, 40g,25g, 10g, 5g, 2500, 1000, 100,
10, half or full
Switch-to-AP(config-if-e1000-1/1/1)#speed-duplex

Re: Icx7250 firmware upgrade now no uplink ports live

Richl — Fri, 17 Feb 2023 00:47:17 GMT

The stack is also up the spout - one unit has no license on the ports now and several other issues would a restore of the config resolve these issues. Also sounds daft but cannot find a diagram of how to cable three icx7250 in a stack unit.

Re: Icx7250 firmware upgrade now no uplink ports live

Richl — Sat, 18 Feb 2023 19:35:09 GMT

Hi no lights on the port and the port is “down” the switch that had the uplink now says it has no configuration and I have tried to reset it on the front panel and this does not work. Having applied an 8 port POD it thinks the speed is 1gb so it won’t stack but it reports 10000 ! I need to wipe this back to factory. Lots of other issues here too!

Re: Icx7250 firmware upgrade now no uplink ports live

Chandini — Mon, 20 Feb 2023 09:31:31 GMT

Hi Richl

Above since its mentioned 7250 firmware upgrade . Could you please confirm if issue started after upgrading the switch ?

If yes then could you help us with firmware which was on switch and firmware the switch was updated to.

Also what is the device you are trying to connect on the port ? Was it a working setup before ?

Thanks

Re: Icx7250 firmware upgrade now no uplink ports live

Richl — Mon, 20 Feb 2023 15:37:34 GMT

Hi All was Fine before starting the upgrade apart from Unit 1 Missing From the Stack

Here is the Story of the Upgrade process:

This was an upgrade on a 3 Switch Stack using a Manifest File via our Brocade BNA Server using its TFTP Repository. The Stack had a Failed Unit over a year ago and the replacement sent was at a Higher Firmware so could not join the stack This would be Unit one

The Stack still had one Connection to the Network Via Unit 3 a POE Switch

Unit 2 still has all the Stack Config but only had 2 x 10GB PODS used for Stacking and cannot connect to the network

The Manifest was to Upgrade from 08.0.30hT211 to 08.0.80fT211 into the Secondary Flash

My connection was lost on Boot System Flash Secondary after seeing the Secondary 80Ft on Sho Flash Stack Units 2 and Stack Unit 3

The Upgrade went as follows:

Copy to unit 3

Sync Image to Unit 3 Flash

Download of ICX7250 Boot Signature Done

Load to Buffer – Automatic copy to Member Units: 3

Syncing Image to Flash

Boot Image Copy is done

Manifest Image download is complete please reload the system

Re: Icx7250 firmware upgrade now no uplink ports live

Chandini — Mon, 20 Feb 2023 17:12:32 GMT

Hi Richl

Noted and Thanks for reverting.

Which was the unit that was swapped in the stack of three units ?

Which unit in the stack had a port issue ?

What is the port number that you have the concern with ?

Thanks

Re: Icx7250 firmware upgrade now no uplink ports live

Richl — Mon, 20 Feb 2023 22:03:21 GMT

Unit 1 failed and was not replaced into the stack as the Firmware of the sent unit was 09 x and it would not be excepted into the stack

Unit 3 is the one in the mess now

Unit 2 did not have a connection to the Network as it had only a 2 port POD license and as a unit it has the config still in place – I added a pod license for all 8 ports but the port is shown as down on ports 4 – 8

Unit 3 will not join a stack as it reports that one of the stacking ports is only 1gb but the command for speed says it’s 10gb

Given the issue is software and I took a backup saved to the BNA server before I touched it would a restore fix the issue . I saved the files as something that means something to me would they need renaming as something else before using?

Re: Icx7250 firmware upgrade now no uplink ports live

Chandini — Tue, 21 Feb 2023 17:37:37 GMT

Hi Richl

Please log a ticket with the below link so that we will help you with further troubleshooting. Thanks

https://support.ruckuswireless.com/contact-us