r720 unleashed PoE+ not working

giuseppe_lamber — Fri, 29 Dec 2017 00:46:08 GMT

Hi All,

I've got a couple of r720 unleashed to run in our small office. They are connected to a Brocade ICX6450-48p
I've ready probably everything about this topic before make my own post, and I'm sure I'm missing something, but I'm really out of ideas 😕
LLDP is enabled on both, AP and Switch, power-over-mdi is advertised by the switch, but yet no luck...the APs are stuck on 802.3af mode

from the switch:

Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/
State State Consumed Allocated Error
--------------------------------------------------------------------------
1/1/1 On Off 0 0 n/a n/a 3 PD Detection Fault
1/1/2 On Off 0 0 n/a n/a 3 n/a
1/1/3 On On 9500 30000 802.3at Class 4 1 n/a

Local port: 1/1/3
Neighbor: 0060.0869.97ef, TTL 113 seconds
+ Chassis ID (MAC address): xxxxxxxxxxxxxx
+ Port ID (MAC address): xxxxxxxxxxxxxx
+ Time to live: 120 seconds
+ System name : "Ruckus-Unleashed"
+ System description : "Ruckus R720 Multimedia Hotzone Wireless AP/SW Ver\
sion: 200.5.10.0.291"
+ System capabilities : bridge, WLAN access point, router
Enabled capabilities: bridge, WLAN access point
+ Management address (IPv4): 192.168.1.7
+ Port description : "ent1"
+ Link aggregation: aggregated (aggregated port ifIndex: 11)
+ 802.3 MAC/PHY : auto-negotiation not supported
Operational MAU type : 1000BaseT-FD
+ 802.3 Power via MDI: PD port
Neighbor: 0060.0869.97ef, TTL 113 seconds
+ Chassis ID (MAC address): xxxxxxxxxxxxxx
+ Port ID (MAC address): xxxxxxxxxxxxxx
+ Time to live: 120 seconds
+ System name : "Ruckus-Unleashed"
+ System description : "Ruckus R720 Multimedia Hotzone Wireless AP/SW Ver\
sion: 200.5.10.0.291"
+ System capabilities : bridge, WLAN access point, router
Enabled capabilities: bridge, WLAN access point
+ Management address (IPv4): 192.168.1.7
+ Port description : "ent2"
+ Link aggregation: aggregated (aggregated port ifIndex: 11)
+ 802.3 MAC/PHY : auto-negotiation not supported
Operational MAU type : 1000BaseT-FD
+ 802.3 Power via MDI: PD port
Neighbor: 0060.0869.97ef, TTL 102 seconds
+ Chassis ID (MAC address): xxxxxxxxxxxxxx
+ Port ID (MAC address): xxxxxxxxxxxxxx
+ Time to live: 120 seconds
+ System name : "Ruckus-Unleashed"
+ System description : "Ruckus R720 Multimedia Hotzone Wireless AP/SW Ver\
sion: 200.5.10.0.291"
+ System capabilities : bridge, WLAN access point, router
Enabled capabilities: bridge, WLAN access point
+ Management address (IPv4): 192.168.1.7
+ Port description : "ent3"
+ Link aggregation: aggregated (aggregated port ifIndex: 11)
+ 802.3 MAC/PHY : auto-negotiation not supported
Operational MAU type : 1000BaseT-FD
+ 802.3 Power via MDI: PD port

From the AP

AP: ID:
1:
MAC Address= xx:xx:xx:xx:xx:xx
Model= r720
Approved= Yes
Device Name= RuckusAP
Device Role= Master
Description=
Location=
GPS=
CERT = Normal
Bonjour-policy=
Bonjour-fencing=
Group Name= System Default
Channel Range:
A/N= 36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,149,153,157,161 (Disallowed= )
B/G/N= 1,2,3,4,5,6,7,8,9,10,11 (Disallowed= )
Radio a/n:
Channelization= Auto
Channel= Auto
WLAN Services enabled= Yes
Tx. Power= Auto
WLAN Group Name= Default
Call Admission Control= OFF
SpectraLink Compatibility= Disabled
Radio b/g/n:
Channelization= Auto
Channel= Auto
WLAN Services enabled= Yes
Tx. Power= Auto
WLAN Group Name= Default
Call Admission Control= OFF
SpectraLink Compatibility= Disabled
Override global ap-model port configuration= No
Network Setting:
Protocol mode= IPv4-Only
Device IP Settings= Manual
IP Address= 192.168.1.7
Netmask= 255.255.255.0
Gateway= 192.168.1.1
Primary DNS Server= 192.168.1.252
Secondary DNS Server= 192.168.1.1
Mesh:
Status= Disabled
LLDP:
Status = Use Parent Setting
LAN Port:
0:
Interface= eth0
Dot1x= None
LogicalLink= Down
PhysicalLink= Down
Label= 10/100/1000 LAN1
1:
Interface= eth1
Dot1x= None
LogicalLink= Up
PhysicalLink= Up 1000Mbps full
Label= 100/1000/2500 PoE LAN2
PoE Mode= Auto
802.3af PoE Tx. chain= 2

LLDP:
Status = Enabled
Interval = 30
HoldTime = 120
Mgmt = Enabled
Ports:
Send out LLDP packet on eth0 = Enabled
Send out LLDP packet on eth1 = Enabled
Send out LLDP packet on eth2 = Enabled
Send out LLDP packet on eth3 = Enabled
Send out LLDP packet on eth4 = Enabled
Send out LLDP packet on eth5 = Enabled

What I'm missing or doing wrong?

Re: r720 unleashed PoE+ not working

giuseppe_lamber — Fri, 29 Dec 2017 13:57:02 GMT

Ok, I've got to the bottom of this issue!

Downgraded from Unleashed to Standalone and ran this on CLI:

set power-mode AT

worked like a charm! Now the AP shows 802.3at as operation mode
The downside is that I've lost any controller feature...is this a limitation of the unleashed firmware? Looks to me that the CLI on unleashed is limited...or at least there's no way to force the power operation mode 😕

Re: r720 unleashed PoE+ not working

mickey_donegan — Fri, 16 Mar 2018 03:24:54 GMT

unleashed CLI--
ruckus(ap-mode)# set power-mode at
OK

Re: r720 unleashed PoE+ not working

hayward_kong — Sat, 31 Mar 2018 07:44:44 GMT

Doesn't work for me on unleashed 205 with r710.. Unknown command. It use to work fine forcing it into at mode with the command., but I'm unleashes 205 doesn't, seem to exist.

Re: r720 unleashed PoE+ not working

greg_mielke — Thu, 26 Jul 2018 06:26:26 GMT

What is the solution here? found config-ap (MAC address). then power-mode 802.3at+ (hit enter) it took.. typed exit.. it saved. rebooted. switch still shows only 9 watts used but class 4????

Re: r720 unleashed PoE+ not working

hyosang_choi — Thu, 26 Jul 2018 08:52:37 GMT

Hi.

Switch is allocated as 30W.

It works properly

You can confirm on Cli on the AP like below.

get power-mode

get lldp pse

topic Re: r720 unleashed PoE+ not working in ICX Switches

r720 unleashed PoE+ not working

Re: r720 unleashed PoE+ not working

Re: r720 unleashed PoE+ not working

Re: r720 unleashed PoE+ not working

Re: r720 unleashed PoE+ not working

Re: r720 unleashed PoE+ not working